Automatic Transmission and A/T Differential

Item
Measurement
Qualification
Standard or New
Service Limit
Automatic transmission fluid
Capacity
Use genuine Honda ATF-Z1
Fluid change
2.9 L (3.1 US qt, 2.5 Imp qt)
Overhaul
6.5 L (6.9 US qt, 5.7 Imp qt)
ATF pressure
Line pressure (K20Z2 engine model)
At 2,000 rpm (min −1 ) in P or N position
900−960 kPa (9.2−9.8 kgf/cm 2 , 130−140 psi)
850 kPa (8.7 kgf/cm 2 , 120 psi)
1st clutch pressure (K20Z2 engine model)
At 2,000 rpm (min −1 ) in 1st gear in M position
890−970 kPa (9.1−9.9 kgf/cm 2 , 130−140 psi)
840 kPa (8.6 kgf/cm 2 , 120 psi)
2nd clutch pressure (K20Z2 engine model)
At 2,000 rpm (min −1 ) in 2nd gear in M position
890−970 kPa (9.1−9.9 kgf/cm 2 , 130−140 psi)
840 kPa (8.6 kgf/cm 2 , 120 psi)
3rd clutch pressure (K20Z2 engine model)
At 2,000 rpm (min −1 ) in 3rd gear in M position
890−970 kPa (9.1−9.9 kgf/cm 2 , 130−140 psi)
840 kPa (8.6 kgf/cm 2 , 120 psi)
4th clutch pressure (K20Z2 engine model)
At 2,000 rpm (min −1 ) in 4th gear in M position
890−970 kPa (9.1−9.9 kgf/cm 2 , 130−140 psi)
840 kPa (8.6 kgf/cm 2 , 120 psi)
5th clutch pressure (K20Z2 engine model)
At 2,000 rpm (min −1 ) in 5th gear in M position
890−970 kPa (9.1−9.9 kgf/cm 2 , 130−140 psi)
840 kPa (8.6 kgf/cm 2 , 120 psi)
Line pressure (K24A3 engine model)
At 2,000 rpm (min −1 ) in P or N position
927−985.6 kPa (9.45−10.05 kgf/cm 2 , 134−142.9 psi)
878 kPa (8.95 kgf/cm 2 , 127 psi)
1st clutch pressure (K24A3 engine model)
At 2,000 rpm (min −1 ) in 1st gear in M position
917−995.4 kPa (9.35−10.15 kgf/cm 2 , 133−144.3 psi)
868 kPa (8.85 kgf/cm 2 , 126 psi)
2nd clutch pressure (K24A3 engine model)
At 2,000 rpm (min −1 ) in 2nd gear in M position
917−995.4 kPa (9.35−10.15 kgf/cm 2 , 133−144.3 psi)
868 kPa (8.85 kgf/cm 2 , 126 psi)
3rd clutch pressure (K24A3 engine model)
At 2,000 rpm (min −1 ) in 3rd gear in M position
917−995.4 kPa (9.35−10.15 kgf/cm 2 , 133−144.3 psi)
868 kPa (8.85 kgf/cm 2 , 126 psi)
4th clutch pressure (K24A3 engine model)
At 2,000 rpm (min −1 ) in 4th gear in M position
917−995.4 kPa (9.35−10.15 kgf/cm 2 , 133−144.3 psi)
868 kPa (8.85 kgf/cm 2 , 126 psi)
5th clutch pressure (K24A3 engine model)
At 2,000 rpm (min −1 ) in 5th gear in M position
917−995.4 kPa (9.35−10.15 kgf/cm 2 , 133−144.3 psi)
868 kPa (8.85 kgf/cm 2 , 126 psi)
Torque converter
Stall speed
Check with vehicle on level ground
K20Z2 engine model
2,100 rpm (min −1 )
1,950−2,250 rpm (min −1 )
K24A3 engine model
2,400 rpm (min −1 )
2,250−2,550 rpm (min −1 )
Clutch - 1/4
Clutch end-plate-to-top disc clearance (K20Z2 engine model)
1st
———
1.23−1.43 mm (0.048−0.056 in.)
2nd
———
0.75−0.95 mm (0.030−0.037 in.)
3rd
———
0.83−1.03 mm (0.033−0.041 in.)
4th and 5th
———
0.73−0.93 mm (0.029−0.037 in.)


Automatic Transmission and A/T Differential (cont'd)

Item
Measurement
Qualification
Standard or New
Service Limit
Clutch - 2/4
Clutch end-plate-to-top disc clearance (K24A3 engine model)
1st
———
0.82−1.02 mm (0.032−0.040 in.)
2nd
———
1.00−1.20 mm (0.039−0.047 in.)
3rd
———
1.00−1.20 mm (0.039−0.047 in.)
4th and 5th
———
0.80−1.00 mm (0.031−0.039 in.)
Clutch return spring free length (K20Z2 engine model)
1st, 2nd, and 3rd
50.8 mm (2.00 in.)
48.8 mm (1.92 in.)
4th and 5th
33.5 mm (1.32 in.)
31.5 mm (1.24 in.)
Clutch return spring free length (K24A3 engine model)
1st and 3rd
38.0 mm (1.50 in.)
36.0 mm (1.42 in.)
2nd
50.8 mm (2.00 in.)
48.8 mm (1.92 in.)
4th and 5th
33.5 mm (1.32 in.)
31.5 mm (1.24 in.)
Clutch disc thickness (K20Z2 engine model)
1st, 2nd, 3rd, 4th, and 5th
1.94 mm (0.076 in.)
———
Clutch disc thickness (K24A3 engine model)
1st and 3rd
1.96 mm (0.077 in.)
———
2nd, 4th, and 5th
1.94 mm (0.076 in.)
———
Clutch plate thickness (K20Z2 engine model)
1st, 2nd, and 3rd
2.00 mm (0.079 in.)
When discolored
4th and 5th
2.30 mm (0.091 in.)
When discolored
Clutch plate thickness (K24A3 engine model)
1st and 3rd
1.6 mm (0.063 in.)
When discolored
2nd, 4th, and 5th
2.0 mm (0.079 in.)
When discolored
Clutch waved-plate phase difference (K20Z2 engine model)
0.07−0.20 mm (0.003−0.008 in.)
0.05 mm (0.002 in.)
Clutch waved-plate phase difference (K24A3 engine model)
0.10−0.20 mm (0.004−0.008 in.)
0.05 mm (0.002 in.)
0.07−0.20 mm (0.003−0.008 in.)
0.05 mm (0.002 in.)



Item
Measurement
Qualification
Standard or New
Service Limit
Clutch - 3/4
1st and 3rd clutch end-plate thickness (K20Z2 engine model)
Mark 1
2.3 mm (0.090 in.)
When discolored
Mark 2
2.4 mm (0.094 in.)
When discolored
Mark 3
2.5 mm (0.098 in.)
When discolored
Mark 4
2.6 mm (0.102 in.)
When discolored
Mark 5
2.7 mm (0.106 in.)
When discolored
Mark 6
2.8 mm (0.110 in.)
When discolored
Mark 7
2.9 mm (0.114 in.)
When discolored
Mark 8
3.0 mm (0.118 in.)
When discolored
Mark 9
3.1 mm (0.122 in.)
When discolored
Mark 10
3.2 mm (0.126 in.)
When discolored
Mark 11
3.3 mm (0.130 in.)
When discolored
Mark 12
3.4 mm (0.134 in.)
When discolored
2nd clutch end-plate thickness (K20Z2 engine model)
Mark 1
2.6 mm (0.102 in.)
When discolored
Mark 2
2.7 mm (0.106 in.)
When discolored
Mark 3
2.8 mm (0.110 in.)
When discolored
Mark 4
2.9 mm (0.114 in.)
When discolored
Mark 5
3.0 mm (0.118 in.)
When discolored
Mark 6
3.1 mm (0.122 in.)
When discolored
Mark 7
3.2 mm (0.126 in.)
When discolored
Mark 8
3.3 mm (0.130 in.)
When discolored
Mark 9
3.4 mm (0.134 in.)
When discolored
4th and 5th clutch end-plate thickness (K20Z2 engine model)
Mark 1
3.0 mm (0.118 in.)
When discolored
Mark 2
3.1 mm (0.122 in.)
When discolored
Mark 3
3.2 mm (0.126 in.)
When discolored
Mark 4
3.3 mm (0.130 in.)
When discolored
Mark 5
3.4 mm (0.134 in.)
When discolored
Mark 6
3.5 mm (0.138 in.)
When discolored
Mark 7
3.6 mm (0.142 in.)
When discolored
Mark 8
3.7 mm (0.146 in.)
When discolored
Mark 9
3.8 mm (0.150 in.)
When discolored


Automatic Transmission and A/T Differential (cont'd)

Item
Measurement
Qualification
Standard or New
Service Limit
Clutch - 4/4
1st and 3rd clutch end-plate thickness (K24A3 engine model)
Mark BA or BK
2.6 mm (0.102 in.)
When discolored
Mark BB or BL
2.7 mm (0.106 in.)
When discolored
Mark BC or BM
2.8 mm (0.110 in.)
When discolored
Mark BD or BN
2.9 mm (0.114 in.)
When discolored
Mark BE or BP
3.0 mm (0.118 in.)
When discolored
Mark BF or BQ
3.1 mm (0.122 in.)
When discolored
Mark BG or BR
3.2 mm (0.126 in.)
When discolored
Mark BH or BS
3.3 mm (0.130 in.)
When discolored
Mark BJ or BT
3.4 mm (0.134 in.)
When discolored
2nd clutch end-plate thickness (K24A3 engine model)
Mark 1
2.6 mm (0.102 in.)
When discolored
Mark 2
2.7 mm (0.106 in.)
When discolored
Mark 3
2.8 mm (0.110 in.)
When discolored
Mark 4
2.9 mm (0.114 in.)
When discolored
Mark 5
3.0 mm (0.118 in.)
When discolored
Mark 6
3.1 mm (0.122 in.)
When discolored
Mark 7
3.2 mm (0.126 in.)
When discolored
Mark 8
3.3 mm (0.130 in.)
When discolored
Mark 9
3.4 mm (0.134 in.)
When discolored
4th and 5th clutch end-plate thickness (K24A3 engine model)
Mark 1
2.1 mm (0.082 in.)
When discolored
Mark 2
2.2 mm (0.086 in.)
When discolored
Mark 3
2.3 mm (0.090 in.)
When discolored
Mark 4
2.4 mm (0.094 in.)
When discolored
Mark 5
2.5 mm (0.098 in.)
When discolored
Mark 6
2.6 mm (0.102 in.)
When discolored
Mark 7
2.7 mm (0.106 in.)
When discolored
Mark 8
2.8 mm (0.110 in.)
When discolored
Mark 9
2.9 mm (0.114 in.)
When discolored



Item
Measurement
Qualification
Standard or New
Service Limit
Mainshaft
Diameter of needle bearing contact area
At stator shaft
22.984−23.000 mm (0.905−0.906 in.)
When worn or damaged
At 5th gear
51.975−51.991 mm (2.046−2.047 in.)
When worn or damaged
At 4th gear collar
33.975−33.991 mm (1.3376−1.3382 in.)
When worn or damaged
I.D. of gears
5th gear
57.000−57.019 mm (2.2441−2.2448 in.)
When worn or damaged
4th gear
40.000−40.016 mm (1.5748−1.5754 in.)
When worn or damaged
End play of gears
5th gear
0.03−0.11 mm (0.001−0.004 in.)
———
4th gear
0.10−0.22 mm (0.004−0.009 in.)
———
41 x 68 mm thrust washer thickness
No. 1
6.35 mm (0.250 in.)
When worn or damaged
No. 2
6.40 mm (0.252 in.)
When worn or damaged
No. 3
6.45 mm (0.254 in.)
When worn or damaged
No. 4
6.50 mm (0.256 in.)
When worn or damaged
No. 5
6.55 mm (0.258 in.)
When worn or damaged
No. 6
6.60 mm (0.260 in.)
When worn or damaged
4th gear collar length
66.3−66.4 mm (2.610−2.614 in.)
———
Length of 4th gear collar flange from end
19.15−19.30 mm (0.754−0.760 in.)
When worn or damaged
Sealing ring thickness
1.91−1.97 mm (0.0752−0.0776 in.)
1.86 mm (0.0732 in.)
Width of sealing ring groove
2.025−2.060 mm (0.0797−0.0811 in.)
2.080 mm (0.0819 in.)
Clutch feed pipe O.D.
7.97−7.98 mm (0.3138−0.3142 in.)
7.95 mm (0.313 in.)
Clutch feed pipe bushing I.D.
8.000−8.015 mm (0.3150−0.3156 in.)
8.030 mm (0.3161 in.)
Countershaft
Diameter of needle bearing contact area
At torque converter housing
36.005−36.015 mm (1.4175−1.4179 in.)
When worn or damaged
At 4th gear
34.982−34.998 mm (1.3772−1.3779 in.)
When worn or damaged
At reverse gear collar
39.979−40.000 mm (1.5740−1.5748 in.)
When worn or damaged
I.D. of gears
4th gear
41.000−41.016 mm (1.6142−1.6148 in.)
When worn or damaged
Reverse gear
46.000−46.016 mm (1.8110−1.8116 in.)
When worn or damaged
End play of gears
5th gear
0−0.48 mm (0−0.019 in.)
———
4th gear
0.04−0.27 mm (0.001−0.011 in.)
———
Reverse gear
0.10−0.25 mm (0.004−0.010 in.)
———
Collar, 35 x 47 x 7.8 mm thickness
7.8 mm (0.31 in.)
———
Distance collar length
57.75−57.80 mm (2.274−2.276 in.)
———
Reverse selector hub width
25.45−25.65 mm (1.002−1.010 in.)
———
Reverse selector hub O.D.
55.87−55.90 mm (2.200−2.201 in.)
When worn or damaged


Automatic Transmission and A/T Differential (cont'd)

Item
Measurement
Qualification
Standard or New
Service Limit
Secondary shaft
Diameter of needle bearing contact area
At 1st gear
39.986−39.999 mm (1.5742−1.5748 in.)
When worn or damaged
At 2nd gear
39.986−39.999 mm (1.5742−1.5748 in.)
When worn or damaged
At 3rd gear collar
36.975−36.991 mm (1.4557−1.4563 in.)
When worn or damaged
I.D. of gears
1st gear
47.000−47.016 mm (1.8504−1.8510 in.)
When worn or damaged
2nd gear
46.000−46.016 mm (1.8110−1.8116 in.)
When worn or damaged
3rd gear
43.000−43.016 mm (1.6929−1.6935 in.)
When worn or damaged
End play of gears
1st gear
0.04−0.12 mm (0.002−0.005 in.)
———
2nd gear
0.04−0.12 mm (0.002−0.005 in.)
———
3rd gear
0.10−0.22 mm (0.004−0.009 in.)
———
37 x 58 mm thrust washer thickness
No. 1
3.900 mm (0.154 in.)
When worn or damaged
No. 2
3.925 mm (0.155 in.)
When worn or damaged
No. 3
3.950 mm (0.156 in.)
When worn or damaged
No. 4
3.975 mm (0.156 in.)
When worn or damaged
No. 5
4.000 mm (0.157 in.)
When worn or damaged
No. 6
4.025 mm (0.158 in.)
When worn or damaged
No. 7
4.050 mm (0.159 in.)
When worn or damaged
No. 8
4.075 mm (0.160 in.)
When worn or damaged
No. 9
4.100 mm (0.161 in.)
When worn or damaged
No. 10
4.125 mm (0.162 in.)
When worn or damaged
No. 11
4.150 mm (0.163 in.)
When worn or damaged
No. 12
4.175 mm (0.164 in.)
When worn or damaged
No. 13
4.200 mm (0.165 in.)
When worn or damaged
No. 14
4.225 mm (0.166 in.)
When worn or damaged
No. 15
4.250 mm (0.167 in.)
When worn or damaged
No. 16
4.275 mm (0.168 in.)
When worn or damaged
No. 17
4.300 mm (0.169 in.)
When worn or damaged
No. 18
4.325 mm (0.170 in.)
When worn or damaged
No. 19
4.350 mm (0.171 in.)
When worn or damaged
No. 20
4.375 mm (0.172 in.)
When worn or damaged
40 x 51.5 mm thrust washer thickness
No. 1
4.80 mm (0.189 in.)
When worn or damaged
No. 2
4.85 mm (0.191 in.)
When worn or damaged
No. 3
4.90 mm (0.193 in.)
When worn or damaged
No. 4
4.95 mm (0.195 in.)
When worn or damaged
No. 5
5.00 mm (0.197 in.)
When worn or damaged
No. 6
5.05 mm (0.199 in.)
When worn or damaged
3rd gear collar length
43.9−44.0 mm (1.728−1.732 in.)
———
Length of 3rd gear collar flange from end
5.25−5.40 mm (0.207−0.213 in.)
When worn or damaged
Sealing ring thickness
1.91−1.97 mm (0.0752−0.0776 in.)
1.86 mm (0.0732 in.)
Width of sealing ring groove
2.025−2.060 mm (0.0797−0.0811 in.)
2.080 mm (0.0819 in.)
Clutch feed pipe O.D.
3rd clutch feed pipe
11.47−11.48 mm (0.4516−0.4520 in.)
11.45 mm (0.4508 in.)
1st clutch feed pipe
6.97−6.98 mm (0.2744−0.2748 in.)
6.95 mm (0.2736 in.)
Clutch feed pipe bushing O.D.
3rd clutch feed pipe
11.500−11.518 mm (0.4528−0.4553 in.)
11.530 mm (0.4539 in.)
1st clutch feed pipe
7.018−7.030 mm (0.2763−0.2768 in.)
7.045 mm (0.2774 in.)
ATF guide of sealing ring contact I.D.
29.000−29.021 mm (1.1417−1.1426 in.)
29.05 mm (1.144 in.)



Item
Measurement
Qualification
Standard or New
Service Limit
Idler gear shaft
Diameter of needle bearing contact area
End cover side
32.003−32.013 mm (1.2600−1.2604 in.)
When worn or damaged
Thickness of cotters
1.39−1.42 mm (0.0547−0.0559 in.)
———
Reverse idler gear
Reverse idler gear shaft diameter at needle bearing contact area
14.99−15.00 mm (0.5902−0.5906 in.)
When worn or damaged
I.D.
20.007−20.020 mm (0.7877−0.7882 in.)
When worn or damaged
I.D. of reverse idler gear shaft contact area on transmission housing
14.800−14.818 mm (0.5827−0.5834 in.)
———
I.D. of reverse idler gear shaft holder
14.800−14.824 mm (0.5827−0.5836 in.)
When worn or damaged
ATF pump
ATF pump thrust clearance
0.03−0.05 mm (0.001−0.002 in.)
0.07 mm (0.003 in.)
ATF pump gear-to-body clearance
Drive gear
0.210−0.265 mm (0.008−0.010 in.)
———
Driven gear
0.070−0.125 mm (0.003−0.005 in.)
———
ATF pump driven gear I.D.
14.016−14.034 mm (0.5518−0.5525 in.)
When worn or damaged
ATF pump driven gear shaft O.D.
13.980−13.990 mm (0.5504−0.5508 in.)
When worn or damaged
Stator shaft
Needle bearing contact I.D.
Torque converter side
27.000−27.021 mm (1.063−1.064 in.)
When worn or damaged
ATF pump side
29.000−29.021 mm (1.1417−1.1426 in.)
———
Sealing ring contact area I.D.
29.000−29.021 mm (1.1417−1.1426 in.)
29.05 mm (1.144 in.)
Reverse shift fork
Fork finger thickness
5.90−6.00 mm (0.232−0.236 in.)
5.40 mm (0.213 in.)
Park gear and pawl
———
———
When worn or damaged
Servo body
Shift fork shaft bore I.D.
14.000−14.010 mm (0.5512−0.5516 in.)
———
Shift fork shaft valve bore I.D.
37.000−37.039 mm (1.4567−1.4582 in.)
37.045 mm (1.4585 in.)
Regulator valve body
Sealing ring contact I.D.
29.000−29.021 mm (1.1417−1.1426 in.)
29.05 mm (1.144 in.)



Item
Measurement
Qualification
Standard or New
Wire Diameter
O.D.
Free Length
No. of Coil
Main valve body spring
Shift valve A spring
0.8 mm (0.031 in.)
5.6 mm (0.220 in.)
28.1 mm (1.106 in.)
15.9
Shift valve B spring
0.8 mm (0.031 in.)
5.6 mm (0.220 in.)
28.1 mm (1.106 in.)
15.9
Shift valve C spring
0.8 mm (0.031 in.)
5.6 mm (0.220 in.)
28.1 mm (1.106 in.)
15.9
Relief valve spring
1.0 mm (0.039 in.)
9.6 mm (0.378 in.)
34.1 mm (1.343 in.)
10.2
Lock-up control valve spring
0.65 mm (0.026 in.)
7.1 mm (0.280 in.)
23.1 mm (0.909 in.)
12.7
Cooler check valve spring
0.85 mm (0.033 in.)
6.6 mm (0.260 in.)
27.0 mm (1.063 in.)
11.3
Servo control valve spring
0.7 mm (0.028 in.)
6.6 mm (0.260 in.)
35.7 mm (1.406 in.)
17.2
Shift valve E spring
0.8 mm (0.031 in.)
5.6 mm (0.220 in.)
28.1 mm (1.106 in.)
15.9


Automatic Transmission and A/T Differential (cont'd)

Item
Measurement
Qualification
Standard or New
Wire Diameter
O.D.
Free Length
No. of Coil
Regulator valve body spring
Stator reaction spring
4.5 mm (0.177 in.)
35.4 mm (1.394 in.)
30.3 mm (1.193 in.)
1.92
Regulator valve spring A
K20Z2 engine model
1.9 mm (0.075 in.)
14.7 mm (0.579 in.)
80.6 mm (3.173 in.)
16.1
K24A3 engine model
1.85 mm (0.073 in.)
14.7 mm (0.579 in.)
83.0 mm (3.268 in.)
14.9
Regulator valve spring B
1.6 mm (0.063 in.)
9.2 mm (0.362 in.)
44.0 mm (1.732 in.)
12.5
Torque converter check valve spring
1.2 mm (0.047 in.)
8.6 mm (0.339 in.)
33.8 mm (1.331 in.)
12.2
Lock-up shift valve spring
1.0 mm (0.039 in.)
6.6 mm (0.260 in.)
35.5 mm (1.398 in.)
18.2
3rd accumulator spring
2.5 mm (0.098 in.)
14.6 mm (0.575 in.)
29.9 mm (1.177 in.)
4.9
1st accumulator spring A
2.4 mm (0.094 in.)
18.6 mm (0.732 in.)
49.0 mm (1.929 in.)
7.1
1st accumulator spring B
2.3 mm (0.091 in.)
12.2 mm (0.480 in.)
31.5 mm (1.240 in.)
6.6
Servo body spring
Shift valve D spring
0.8 mm (0.031 in.)
5.6 mm (0.220 in.)
28.1 mm (1.106 in.)
15.9
4th accumulator spring B
2.3 mm (0.091 in.)
12.2 mm (0.480 in.)
31.5 mm (1.240 in.)
6.6
4th accumulator spring A
2.4 mm (0.094 in.)
18.6 mm (0.732 in.)
49.0 mm (1.929 in.)
7.1
2nd accumulator spring B
K20Z2 engine model
2.0 mm (0.079 in.)
10.6 mm (0.417 in.)
34.0 mm (1.339 in.)
8.0
K24A3 engine model
2.1 mm (0.083 in.)
10.8 mm (0.425 in.)
34.0 mm (1.339 in.)
8.2
2nd accumulator spring A
K20Z2 engine model
2.2 mm (0.087 in.)
16.6 mm (0.654 in.)
48.2 mm (1.898 in.)
8.5
K24A3 engine model
2.1 mm (0.083 in.)
16.6 mm (0.654 in.)
48.7 mm (1.917 in.)
8.4
5th accumulator spring
2.5 mm (0.098 in.)
14.6 mm (0.575 in.)
29.9 mm (1.177 in.)
4.9



Item
Measurement
Qualification
Standard or New
Service Limit
A/T differential carrier
Pinion shaft contact area I.D.
18.000−18.025 mm (0.708−0.710 in.)
———
Carrier-to-pinion shaft clearance
0.023−0.057 mm (0.001−0.002 in.)
0.1 mm (0.004 in.)
Driveshaft contact area I.D.
28.015−28.045 mm (1.103−1.104 in.)
———
Carrier-to-driveshaft clearance
0.035−0.086 mm (0.001−0.003 in.)
0.12 mm (0.005 in.)
Carrier bearing starting torque (preload)
For new bearing
2.7−3.9 N·m (28−40 kgf·cm, 24−35 lbf·in.)
Adjust
For used bearing
2.5−3.6 N·m (25−37 kgf·cm, 22−32 lbf·in.)
Adjust
Final driven gear backlash
References
0.087−0.146 mm (0.003−0.006 in.)
0.2 mm (0.008 in.)
A/T differential pinion gear
Backlash
0.05−0.15 mm (0.002−0.006 in.)
———
I.D.
18.042−18.066 mm (0.7103−0.7113 in.)
———
Pinion gear-to-pinion shaft clearance
0.055−0.095 mm (0.0022−0.0037 in.)
0.12 mm (0.005 in.)