Summary of Contents for Honda Accord 1994-1995-62SN722 Service Manual - Page 33

  • Honda Accord 1994-1995-62SN722 Service Manual - Page 33

    Standards and Service Limits Unit o( lungth mm (in) ’— Air Con I ioning — Section 22 MEAsIJREMEm STANDARD (new) Air condilloning Lubricant type: ~00le; masses - PH7 7 003 (For Relrigeram HFc-ma (mam) WSW Lubricant capacllv Condenser 107 20 (1/3 — m, 0.4 — 0.7) ml (11 oz, Imp oz) Evaporator 20 7 :10 (2/3 7 .07 _ 1.1) Line or note 10 (1/3, 0.11) Receiver 10 (1/3, 0.4) Compressor Lubncant type: ND-OILB P/N38899 7 pm 7 00:) (For Refrigerant NFC-1343 (it-134a” Lubricant capacity rnl (ll 01, imp 01) 160 1:15-03 F. 5.0?) Stator coil resistance at 20°: (sear) n 3.5 1 0.2 Pulleytopressure plate clearance 0‘5 1 W5 (0-020 t 0-005! Compressor Deflection with 101) N (1)) kg, 22 lbs) 10.0 — 12.01039 7 0.47) with used oelt belt~ between the pulleys 4.5 7 1.0 (0.15 7 0 28) with new belt Belt tension N (kg, lbs) Measured with belt tension gauge A50 7 500 (45 - so, 99 7 132) with used belt 950 - (.150 (95 7 H5, 205 - 25‘) will) new belt — Electrical —— 5 action 23 MEASUREMENT STANDARD (NEW) Ignition coil Rated voltage v 12 Primary winding resistance 0 at 20°C (58°F) 0.6 7 0.8 Secondary winding resistance m at 204C (68°F) 13 — 19 Spark Plug Wpe See section 23 (Supplement 53 code No, 625N720) Gap 1.0 7 (.1 (0.009 7 0.003) Ignition ttming At idle ° BTDC l512lRed) Alternator belt’ Without A/C Deflection with 100 N (lo kg, 22 lbs) (0 — 12 (0.39 7 (1‘7) with used belt between pulleys 8.5 — ii (0.33 7 0.13) with new belt Belt tension N (kg, lbs) 300 - 450 (30 7 ‘5, es 7 99) with used belt Measured with belt tension gauge (50 7 650145 7 05, 99 7 113) With new belt With A/C Deflection with 100 N (10 kg, 22 lbs) 10— 12 (0.39 7 0.47) with used belt between pulleys (.5 7 7 (0.18 7 0.28) with new belt Belt tension N (kg, lbs) 450 7 600 (45 7 so, 99 - 132) with used bell Measured with belt tension gauge 950 71,150(95 7 115, 209 - 254) With new belt Brush spring tension 9 (oz) MEASUREMEM SYANDARD (NEW) SERVICE qur Alternator Output 115 V at hot A 70/80 ¥ (:oil resistance (rotor) u 2.3 7 3,0 7 ng 0.0. 1“ (0.51) 11.0 (0.55) Brush length 10.5 (0.41) 5.5 (022) 300-360 (106- I27) Starter motor YVDe Mice depth Commutator (uncut Commutetor 0)). Brush length Brush spring tension (new) N (kg, lbs) Spur gear reduction, permlrlenl magnet 04 - 0.5 (0.016 - 0.020) 0.15 (0.006) 0 7 0 02 (0 - 0.0005) 0.05 (0.002) 28.0-28.1 (1.1027t.l061 27.5(l.08) 15.5 - 16.2 (0.62 - 0.64) 10.0 (0.39,) 1071011.s- 1.3, 3571.0) * When using a new belt, adiuet deflection or tension to new values. Run the engine (or 5 minutes then turn it ofl. Readjust deflection or tension to used belt values. 3-14