Summary of Contents for Honda Accord 1996 62SN723 Service Manual - Page 24

  • Honda Accord 1996 62SN723 Service Manual - Page 24

    — Air Conditioni ng — Section 22 Unit oi length: mm (in) MEASUREMENT STANDARD (NEW) Air condinomng Lubrlcam type: NDrOILB P/Naasss 7 PR7 7 003 or 35399 7 PR7 7 A01 (For Relrigerant Hcha (Ii-134m) SYS‘E Lubricant capacin Condenser 10 7 20 (1/3 7 213,0.4 7 0.7) ml (ll 01, Imp oz) Evaporalur 20730(2/371,0.721.i) Line or note 10 (1/3, 0.4) Receiver 10 (1/3, 0.4) _ Compressor Luoncent type: ND-OILB P/N33399 7 PR7 7 003 or 35090 7 PR7 — A01 (For Refrigerant HFc7134a(R-)34s)) Luhrlcant capaciw mi (fl oz, Imp 01) I60 IP (571/3 ‘7)”. 5.5 “35) Slam! coil resistance a! 20°C (68°F) D ‘5 t 0.2 Pulleyslorpvessure plale clearance 0.5 e 0.15 (0.020 : 0.006) compressor Deileclion wun 100 N ((0 kg, 22 lbs) 10.07 12.0 (0.39 7 0.47) With used bell belt belween tne pulleys 4.5 7 7.0 (0.13 7 .28) with new belt Bell lsnSion N (kg, lbs) Measured with belt tension gauge 450 7 600 (45 7 60, 99 7 132) wilh used bell 950 71,150195 7115, 209 7 254) with new belt — Electrical — Section 23 MEASUREMEm STANDARD (NEW) Ignition coil Rated vollage v (z Frlmarv Wln ng resistance 0 at 20~c (63*) 0.5 7 0.8 Secondary windlng leslsmnce m 512?!) (63°F) 13 710 Spark Plug Type See section 23 Gap 1,! J5. (moaned) Ignition timing At idle ° ETDC 15 1 2 (Red) Alternator belt- witnout A/C Deflection with 100 N (10 kg, 22 lbs) lo 712 (0.30 7 0.07) with used bsll between pulleys 5.5 7 11 (0.33 7 0.43) With new beli Bell (ensi n N (kg, lbs) 300 7 :50 (30 7 45. as 7 99) unit. used belt Measured wltn bell |en5lun gauge (50 7 550 (45 7 05, 99 7 (a) with new belt Witn A/C Dellectlon w)lh 100 N (10 kg, 22 lbs) 10 712 (0.397 0.47) wiih used ball between pulleys 4.5 - 7 (0.10 7 0.23) wilh new belt Ball lensiun N (kg, lbs) 450 - GOD (45 -60, 99 - 132) wllh used be“ Measured with ball tension gauge 950 7i.150(95 7115.209 7 254) with new belt Erush Spring tension 5] (oz) MEASUREMENT STANDARD (NEW) SERVICE LIMIT Alierneior Output (3.5 v at hot A 70 7 Coil resistance (rotor) r) 2,8 7 3.0 Slip ring 00. 14.4 (0.57) u.0 (0.55) Brush length 10.5 (0.41) 5.5 (0.22) 300 7 360 (10.6 711.7) Starter motor Tyne Mica depin Commulmor runout Commulamv 0.0. Brush length Brush spring tension (new) N (kg, lbs) Spur gear reduction, permanent magnet 0.5 7 0.5 (time 7 0.020) 0.15 (0.006) 0 - 0 02 (0 - 0.0008) 0.05 (0.002) 28.0—28.1 (1.10271 los) 27,5(1.08) 15.87161 (0.62-0.64) 10,001.33) 1671305713357‘9) When using a new belt, aaiust deflectlon ortension to new values, Run the engine fo( 5 minutes then turn it on. Reudjusi deflection orlensicln 10 used Dell values 3-11