Summary of Contents for Honda Accord 1996 62SN724 Service Manual - Page 41

  • Honda Accord 1996 62SN724 Service Manual - Page 41

    12M124© © 20. Restrain camshaft gear using tool IEG 1521 . 21. Remove camshaft gear retaining bolt and discard. 22 Remove tool 186 1521 . 23. Release camshaft gear from camshaft and remove from belt. CAUTION: II the sinlered gears have been sub/acted to prolonged oil contammatlon. they must be soaked in a solvent bath and thoroughly washed wrth solvent before refitment. Because 0! the porous construction a! the srntered material. oil impregnated In the gear will emerge and contaminate a new belt. CAUTION: If camshaft trming belt shows any sign of or! contamination renew camshaft timing belt. see MAINTENANCE 24. Fit but do not tighten the old camshaft gear retaining boll. 13G1475 28 CE 1 l a) _ 26 29 r— 12M1364 25. Fit and tighten seal remover. tool 186 1476 . to camshaft seal. 26. Tighten seal remover centre screw to remove camshatt seal. . Remove seal remover. tool 185 1476 . . Remove and discard seal from seal remover tool. 29. Remove and discard camshaft gear retaining bolt. 88 Hell 1 ENGINE 113%] l . Clean seal recess and camshaft. 2. Grease outer edge of new seal. 3. Lubricate the inner lip of the seal with clean engine oil. 186 1716 12M1365 4. Ensure seal fitting tool 186 1716 is clean. 5. Locate new oil seal to seal housing, 5 7 8 position tool 186 1716to seal and drift seal into housing. . Remove tool 186 1716. . Clean camshaft gear. . Fit camshaft gear to belt and position gear to camshaft. CAUTION: Ensure timing marks on camshaft gear and rear cover are aligned. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. Restrain camshaft gear using tool 186 1521. Apply clean engine oil to threads of new bolt, fit camshaft gear bolt and tighten to 20 N~m (2.0 kgt~m, 15 lbf-fll + 90°. Remove tool 188 1521. Fit engine RH mounting assembly. Lower engine on jack to align engine mounting assembly. Fit 3 bolts securing engine mounting to engine and tighten to 85 N~m (8.7 kgf~m, 53 lbf~ft). Fit restraint bar to engine mounting, fit and tighten nuts to 45 N~m (4.6 kgf-m, 33 lbf‘ft). Fit mounting tie bar to body bracket, fit and tighten bolt to 90 Nm (9.2 kgf-m, 66 lbf‘ft). Tighten bolt securing mounting tie barto mounting to 90 N~m (9.2 kgf-m, 68 lbf~ft). Remove trolley jack from vehicle. Slacken tensioner pulley Allen bolt. Release camshaft timing belt tansioner plunger using tool 18G 1719. Remove tool 186 1719 from camshaft timing belt tensioner. Remove timing pin tool 186 1523 from flywheel. Rotate crankshaft 2 complete revolutions and align camshaft gear timing marks. CAUTION: Do not exceed the specified torque figure. 24 25 . Position camshaft timing belt top cover. fit 4 bolts and tighten to 5 N-m (0.5 kgf-m, 4 Ibf-ft). . Remove stand(s) and lower vehicle. REPAIRS 3