Front Knuckle/Hub Replacement

Exploded View

 

Special Tools Required
Attachment, 78 x 90 mm (  07GAD-SD40101)
 

Hub dis/assembly tool (  07GAF-SE00100)
 
Ball joint remover, 32 mm (  07MAC-SL00101)
 
Ball joint remover, 28 mm (  07MAC-SL00201)
 
Attachment, 62 x 68 mm (  07746-0010500)
 
Driver (  07749-0010000)
 
Support base (  07965-SD90100)
 


Knuckle/Hub Replacement


1.Raise the front of the vehicle, and support it with safety stands in the proper locations.

2.Remove the wheel nuts (A) and front wheel.

 

3.Remove the brake hose mounting bolt (A).

 

4.Remove the brake caliper bracket mounting bolts (B), and remove the caliper assembly (C) from the knuckle. To prevent damage to the caliper assembly or brake hose, use a short piece of wire to hang the caliper assembly from the undercarriage. Do not twist the brake hose excessively.

5.Remove the wheel sensor (A) from the knuckle (B). Do not disconnect the wheel sensor connector.

 

6.Raise the stake (A), then remove the spindle nut (B).

 

7.Remove the 6 mm brake disc retaining screws (A).

 

8.Remove the brake disc (B) from the front hub.

NOTE: If the brake disc has clung to the front hub. Screw two 8 x 1.25 mm bolts (C) into the brake disc to push it away from the hub. Turn each bolt 90 degrees at a time to cocking the brake disc from binding.

9.Check the front hub for damage and cracks.

10.Remove the cotter pin (A) from the tie-rod end ball joint, then remove the nut (B).

NOTE: During installation, install a new cotter pin after tightening the nut, and bend its end as shown.

 

11.Disconnect the tie-rod ball joint from the knuckle using the special tool.

12.Remove the flange bolt (A) and flange nuts (B) from the lower arm (C).

NOTE: During installation, install a new flange bolt and new flange nuts. After lightly tightening all three fasteners, tighten them to the specified torque beginning with the flange nuts.

 

13.Disconnect the lower ball housing from the lower arm.

14.Remove the damper pinch bolts (A) and self-locking nuts (B) from the damper.

NOTE: During installation, install the new damper pinch bolts and new self-locking nuts.

 

15.Remove the driveshaft outboard joint (C) from the knuckle (D) by tapping the driveshaft end (E) with a plastic hammer while drawing the hub outward, then remove the knuckle.

NOTE: Do not pull the driveshaft end outward. The inner driveshaft joint may come apart.

16.Remove the lock pin (A) from the lower ball housing (B), then remove the nut (C).

NOTE: During installation, install a new lock pin after tightening the new castle nut.

 

17.Disconnect lower ball housing from the knuckle using the special tools.

18.Install the knuckle/hub in the reverse order of removal, and note these items:

  • Be careful not to damage the ball joint boot when installing the knuckle.
  • Tighten all mounting hardware to the specified torque values.
  • Before connecting the lower ball joint to the knuckle, degrease the threaded section and tapered portion of the ball joint pin, the knuckle connecting hole, the threaded section, and mating surface of the castle nut.
  • First install all the components, and lightly tighten the bolts and nuts, then raise the suspension to load it with the vehicle's weight before fully tightening to the specified torque values.
  • Torque the castle nut to the lower torque specification, then tighten it only far enough to align the slot with the ball joint pin hole. Do not align the castle nut by loosening it.
  • Use a new spindle nut during reassembly.
  • Before installing the spindle nut, apply a small amount of engine oil to the seating surface of the nut. After tightening, use a drift to stake the spindle nut shoulder against the driveshaft.
  • Before installing the brake disc, clean the mating surface of the front hub and the inside of the brake disc.
  • Before installing the wheel, clean the mating surface of the brake disc and the inside of the wheel.
  • Check the wheel alignment, and adjust it if necessary.

Wheel Bearing Replacement


1.Separate the hub (A) from the knuckle (B) using the special tool and a hydraulic press. Hold the knuckle with the attachment (C) of the hydraulic press or equivalent tool. Be careful not to deform the splash guard. Hold onto the hub to keep it from falling when pressed clear.

 

2.Press the wheel bearing inner race (A) off of the hub (B) using the special tool, a commercially available bearing separator (C), and a press.

 

3.Remove the splash guard (A) and the snap ring (B) from the knuckle (C).

 

4.Press the wheel bearing (A) out of the knuckle (B) using the special tools and a press.

 

5.Wash the knuckle and hub thoroughly in high flash-point solvent before reassembly.

6.Press a new wheel bearing (A) into the knuckle (B) using the old bearing (C), a steel plate (D), the special tool, and a press.

NOTE:
  • Install the wheel bearing with the wheel sensor magnetic encoder (E) (brown color), toward the inside of the knuckle.
  • Remove any oil, grease, dust, metal debris, and other foreign material from the encoder surface.
  • Keep all magnetic tools away from the encoder surface.
  • Be careful not to damage the encoder surface when you insert the wheel bearing.

Except K20Z2 engine model 

K20Z2 engine model 

7.Install the snap ring (A) securely in the knuckle (B).

 

8.Install the splash guard (C), and tighten the screws (D) to the specified torque value.

9.Install the hub (A) onto the knuckle (B) using the special tools shown and a hydraulic press. Be careful not to distort the splash guard (C).

Except K20Z2 engine model 

K20Z2 engine model