DTC Troubleshooting: U0107 (30)

DTC U0107:  Lost Communication With Throttle Actuator Control Module

1.Turn the ignition switch ON (II).

2.Clear the DTC with the HDS.

3.Check for Temporary DTCs or DTCs with the HDS.

Is DTC U0107 indicated?


YES - Check for poor connections or loose terminals at the throttle body, the throttle actuator control, module and the ECM/PCM, then go to 50. If the connections are OK, go to 6.


NO - Go to 4.


4.Start the engine.

5.Check for Temporary DTCs or DTCs with the HDS.

Is DTC U0107 indicated?


YES - Go to 46.


NO - Intermittent failure, system is OK at this time. Check for poor connections or loose terminals at the throttle body, the throttle actuator control module relay, the throttle actuator control module, and the ECM/PCM.n


6.Clear the DTC with the HDS.

7.Turn the ignition switch OFF.

8.Disconnect the intake air duct from the throttle body.

9.Press the accelerator pedal to the floor.

10.Turn the ignition switch ON (II).

11.Check the throttle valve operation.

Does it open after the throttle valve closes?


YES - Go to 12.


NO - Go to 13.

12.Check the throttle valve again.

Does the throttle valve open fully?


YES - Go to 40.


NO - Go to 34.


13.Turn the ignition switch OFF.

14.Disconnect the throttle actuator control module 16P connector.

15.Check for continuity between throttle actuator control module 16P connector terminal No. 7 and body ground.

 

Is there continuity?


YES - Go to 16.


NO - Repair open in the wire between the throttle body, the throttle actuator control module, and G101, then go to 50.

16.Remove the throttle actuator control module relay (A).

 

17.Measure voltage between throttle actuator control module relay terminal No. 1 and body ground.

 

Is there battery voltage?


YES - Go to 19.


NO - Go to 18.


18.Check the No. 8 DBW (THROTTLE ACTUATOR CONTROL) (15 A) fuse in the under-dash fuse/relay box.

Is the fuse OK?


YES - Repair open in the wire between the throttle actuator control module relay (+B line) and the No. 8 DBW (THROTTLE ACTUATOR CONTROL) (15 A) fuse, then go to 50.


NO - Repair short in the wire between the throttle actuator control module relay (+B line) and the No. 8 DBW (THROTTLE ACTUATOR CONTROL) (15 A) fuse, then go to 50.

19.Install the throttle actuator control module relay.

20.Measure voltage between throttle actuator control module 16P connector terminal No. 2 and body ground.

21.Turn the ignition switch ON (II).

 

Is there battery voltage for about 2 seconds?


YES - Substitute a known-good throttle actuator control module, then go to 50 and recheck. If DTC U0107 is not indicated, replace the original throttle actuator control module, then go to 50.


NO - Go to 22.


22.Turn the ignition switch OFF.

23.Remove the throttle actuator control module relay (A).

 

24.Check the throttle actuator control module relay.

Is the throttle actuator control module relay OK?


YES - Go to 25.


NO - Replace the throttle actuator control module relay, then go to 50.


25.Turn the ignition switch ON (II).

26.Measure voltage between throttle actuator control module relay terminal No. 4 and body ground.

 

Is there battery voltage?


YES - Go to 27.


NO - Repair open in the wire between the throttle actuator control module relay and PGM-FI main relay 1, then go to 50.


27.Turn the ignition switch OFF.

28.Jump the SCS line with the HDS.

29.Disconnect ECM/PCM connector D (17P).

30.Check for continuity between ECM/PCM connector terminal D15 and throttle actuator control module relay terminal No. 3.

 

Is there continuity?


YES - Go to 31.


NO - Repair open in the wire between the ECM/PCM (D15) and the throttle actuator control module relay, then go to 50.


31.Check for continuity between throttle actuator control module 16P connector terminal No. 2 and body ground.

 

Is there continuity?


YES - Repair short in the wire between the throttle actuator control module and the throttle actuator control module relay (+B line), then go to 50.


NO - Go to 32.

32.Connect throttle actuator control module relay terminal No. 2 to body ground with a jumper wire.

 

33.Check for continuity between throttle actuator control module 16P connector terminal No. 2 and body ground.

 

Is there continuity?


YES - Go to 56.


NO - Repair open in the wire between the throttle actuator control module and the throttle actuator control module relay (+B line), then go to 50.

34.Turn the ignition switch OFF.

35.Jump the SCS line with the HDS.

36.Disconnect the throttle actuator control module 16P connector.

37.Disconnect ECM/PCM connector B (24P).

38.Check for continuity between ECM/PCM connector terminal B19 and body ground.

 

Is there continuity?


YES - Repair short in the wire between the ECM/PCM (B19) and the throttle actuator control module, then go to 50.


NO - Go to 39.

39.Check for continuity between ECM/PCM connector terminal B19 and throttle actuator control module 16P connector terminals No. 6.

 

Is there continuity?


YES - Substitute a known-good throttle actuator control module, then go to 50 and recheck. If DTC U0107 is not indicated, replace the original throttle actuator control module, then go to 50. If DTC U0107 is indicated, go to 56.


NO - Repair open in the wire between the ECM/PCM (B19) and the throttle actuator control module, then go to 50.

40.Turn the ignition switch OFF.

41.Jump the SCS line with the HDS.

42.Disconnect the throttle actuator control module 16P connector.

43.Disconnect ECM/PCM connector B (24P).

44.Check for continuity between ECM/PCM connector terminal B20 and body ground.

 

Is there continuity?


YES - Repair short in the wire between the ECM/PCM (B20) and the throttle actuator control module, then go to 50.


NO - Go to 45.

45.Check for continuity between ECM/PCM connector terminal B20 and throttle actuator control module 16P connector terminal No. 14.

 

Is there continuity?


YES - Substitute a known-good throttle actuator control module, then go to 50 and recheck. If DTC U0107 is not indicated, replace the original throttle actuator control module, then go to 50. If DTC U0107 is indicated, go to 56.


NO - Repair open in the wire between the ECM/PCM (B20) and the throttle actuator control module, then go to 50.

46.Turn the ignition switch OFF.

47.Jump the SCS line with the HDS.

48.Disconnect ECM/PCM connector A (31P).

49.Check for continuity between body ground and ECM/PCM connector terminals A8 and A9 individually.

 

Is there continuity?


YES - Check for poor connections or loose terminals at the throttle body, the throttle actuator control module relay, the throttle actuator control module, and the ECM/PCM, then go to 1.


NO - Repair open in the wire between the ECM/PCM (A8, A9) and G101, then go to 50.

50.Turn the ignition switch OFF.

51.Reconnect all connectors.

52.Turn the ignition switch ON (II).

53.Reset the ECM/PCM with the HDS.

54.Do the ECM/PCM idle learn procedure.

55.Check for Temporary DTCs or DTCs with the HDS.

Are any Temporary DTCs or DTCs indicated?


YES - If DTC U0107 is indicated, check for poor connections or loose terminals at the throttle body,the throttle actuator control module relay, the throttle actuator control module, and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.


NO - Troubleshooting is complete.n


56.Update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM.

57.Check for Temporary DTCs or DTCs with the HDS.

Are any Temporary DTCs or DTCs indicated?


YES - If DTC U0107 is indicated, check for poor connections or loose terminals at the throttle body, the throttle actuator control module relay, the throttle actuator control module, and the ECM/PCM, then go to 1. If any other Temporary DTCs or DTCs are indicated, go to the indicated DTC's troubleshooting.


NO - If the ECM/PCM was updated, troubleshooting is complete. If the ECM/PCM was substituted, replace the original ECM/PCM.n