- Put on gloves to protect your hands.
- Wear eye protection when removing the glass with piano wire.
- Use seat covers to avoid damaging the seat.
- Use glass adhesive set P/N. 08C73-X0230N.
|1.||Remove these items:|
|2.||Remove the molding (A) from the edge of the windshield (B). If necessary, cut the molding with a utility knife.|
|3.||If the old windshield is to be reinstalled, make alignment marks across the glass and body with a grease pencil.|
|4.||Pull down the front portion of the headliner. Take care not to bend the headliner excessively, or you may crease or break it.|
|5.||Apply protective tape along the edge of the dashboard and body. Using an awl, make a hole through the rubber dam, adhesive, and dashboard seal from inside the vehicle at the corner portion of the windshield. Push a piece of piano wire through the hole, and wrap each end around a piece of wood.|
|6.||With a helper on the outside, pull the piano wire (A) back and forth in a sawing motion. Hold the piano wire as close to the windshield (B) as possible to prevent damage to the body and dashboard.|
Carefully cut through the rubber dam and adhesive (C) around the entire windshield.
|7.||Carefully remove the windshield.|
|8.||With a knife, scrape the old adhesive smooth to a thickness of about 2 mm (0.08 in.) on the bonding surface around the entire windshield opening flange:|
|9.||Clean the body bonding surface with a sponge dampened in alcohol. After cleaning, keep oil, grease and water from getting on the clean surface.|
|10.||If the old windshield is to be reinstalled, use a putty knife to scrape off all of the old adhesive, the fasteners and the rubber dam from the windshield. Clean the inside face and the edge of the windshield with alcohol where new adhesive is to be applied. Make sure the bonding surface is kept free of water, oil and grease.|
|11.||Glue the upper rubber dam (A), corner rubber dams (B), lower rubber dam (C) and fasteners (D) to the inside face of the windshield (E) as shown:|
|12.||Glue the molding (A) with adhesive tape (B) to the edge of the windshield (C):|
|13.||Install the fasteners (A) to the body.|
|14.||Set the windshield in the opening, and center it.|
Make alignment marks (A) across the windshield and body with a grease pencil at the four points shown. Be careful not to touch the windshield where adhesive will be applied.
|15.||Remove the windshield.|
|16.||With a sponge, apply a light coat of glass primer around the edge of the windshield (A) between the dams (B) and molding (C) as shown, then lightly wipe it off with gauze or cheesecloth:|
|17.||With a sponge, apply a light coat of body primer to the original adhesive remaining around the windshield opening flange. Let the body primer dry for at least 10 minutes:|
|18.||Before filling a cartridge, cut a ‘‘V'' in the end of the nozzle (A) as shown.|
|19.||Pack adhesive into the cartridge without air pockets to ensure continuous delivery. Put the cartridge in a caulking gun, and run a bead of adhesive (A) around the edge of the windshield (B) between the dams (C) and molding (D) as shown. Apply the adhesive within 30 minutes after applying the glass primer. Make a slightly thicker bead at each corner.|
|20.||Use suction cups to hold the windshield over the opening, align it with the alignment marks made in step 14, and set it down on the adhesive. Lightly push on the windshield until its edges are fully seated on the adhesive all the way around. Do not open or close the doors until the adhesive is dry.|
|21.||Scrape or wipe the excess adhesive off with a putty knife or towel. To remove adhesive from a painted surface or the windshield, wipe with a soft shop towel dampened with alcohol.|
|22.||Let the adhesive dry for at least 1 hour, then spray water over the windshield and check for leaks. Mark leaking areas, and let the windshield dry, then seal with sealant:|
|23.||Reinstall all remaining removed parts. Install the rearview mirror after the adhesive has dried thoroughly. Advise the customer not to do the following things for 2 to 3 days:|