Honda CIVIC 10G 2016 Engine Lubrication System Page 1

Engine Lubrication System Description - Engine Oil Monitor System
General Description
The engine oil monitor system shows a driver when the engine oil and/or the engine oil filter should be replaced by indicating a caution
on the gauge control module which means the period of time when they should be replaced.
Item A: Replace engine oil.
Item B: Replace engine oil and engine oil filter.
The engine oil monitor system helps the engine to keep a good condition.
The PCM calculates a current driving condition, an engine load, and an appropriate engine oil replacement period, then, according to
the result of the calculations, it displays a caution on the gauge control module.
NOTE: The illustration shows an image.
Fail-Safe Action
If the PCM stores engine system DTC(s), it will not be able to properly calculate the current driving condition because of the fail-safe
action. Instead, the PCM calculates a temporary driving condition in theory and results in a replacement period earlier than normal
with a
caution display on the gauge control module.
Engine Lubrication System Description - Engine Oil Monitor System 1944 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/...
1 of 1 12/20/2018 6:36 AM
cardiagn.com

Contents Summary of Engine Lubrication System

  • Page 1Engine Lubrication System Description - Engine Oil Monitor System General Description The engine oil monitor system shows a driver when the engine oil and/or the engine oil filter should be replaced by indicating a caution on the gauge control module which means the period of time when they should b
  • Page 2Engine Lubrication System Description - Hydraulic Circuit Hydraulic Circuit cardiagn.com
  • Page 3cardiagn.co
  • Page 4Engine Lubrication System Description - Hydraulic Circuit Hydraulic Circuit cardiagn.com
  • Page 5cardiagn.co
  • Page 6Engine Lubrication System Description - Hydraulic Circuit Hydraulic Circuit cardiagn.com
  • Page 7cardiagn.co
  • Page 8Engine Lubrication Circuit Diagram cardiagn.com
  • Page 9Engine Lubrication Circuit Diagram cardiagn.com
  • Page 10Engine Lubrication System Component Location Index cardiagn.com
  • Page 11cardiagn.co
  • Page 12Engine Lubrication System Component Location Index cardiagn.com
  • Page 13cardiagn.co
  • Page 14cardiagn.co
  • Page 15Engine Lubrication System Component Location Index cardiagn.com
  • Page 16cardiagn.co
  • Page 17cardiagn.co
  • Page 18Engine Lubrication System Symptom Troubleshooting - Low oil pressure indicator does not come on with the vehicle in the ON mode cardiagn.com Low oil pressure indicator does not come on with the vehicle in the ON mode 1. Gauge control module test: ‐1. Connect the HDS to the DLC. ‐2. Check for DTCs. I
  • Page 19‐1. Turn the vehicle to the OFF (LOCK) mode. ‐2. Jump the SCS line with the HDS, and wait more than 1 minute. NOTE: This step must be done to protect the PCM from damage. ‐3. Disconnect the following connectors. PCM connector E (80P) Oil pressure switch 1P connector ‐4. Check for continuity between
  • Page 20Engine Lubrication System Symptom Troubleshooting - Low oil pressure indicator stays on cardiagn.com Low oil pressure indicator stays on 1. Gauge control module test: ‐1. Connect the HDS to the DLC. ‐2. Check for DTCs. If a DTC is present, diagnose, and repair the cause before continuing with this t
  • Page 21‐2. Jump the SCS line with the HDS, and wait more than 1 minute. NOTE: This step must be done to protect the PCM from damage. ‐3. Disconnect the following connectors. PCM connector E (80P) Oil pressure switch 1P connector ‐4. Check for continuity between test points 1 and 2. Test condition Vehicle O
  • Page 22Engine Lubrication System Symptom Troubleshooting Index Symptom Diagnostic procedure Also check for Excessive engine oil consumption 1. Check for oil leaks. Check the maintenance records 2. Check for worn valve guide(s); or worn as engine oil that is valve seal(s). worn out burns off at 3. Check for
  • Page 23Engine Oil Filter Feed Pipe Removal and Installation 1. Oil Filter - Remove 2. Oil Filter Feed Pipe - Remove 1. Oil Filter Feed Pipe - Install cardiagn.com 1. Install the two 20 x 1.5 mm nuts (A) onto the oil filter feed pipe. Hold one nut with a wrench, then use a second wrench to tighten the other
  • Page 243. Install the oil filter feed pipe in its specified height range shown. 4. Remove the nuts from the oil filter feed pipe. 2. Oil Filter - Install cardiagn.com
  • Page 25Engine Oil Filter Feed Pipe Removal and Installation NOTE: Where icon is shown, click for further information. 1 cardiagn.com Detailed information, notes, and precautions
  • Page 261. Oil Filter - Remove cardiagn.com
  • Page 272. Oil Filter Feed Pipe - Remove Note for installation 1. Install the two 20 x 1.5 mm nuts (A) onto the oil filter feed pipe. Hold the nut with a wrench, then tighten the other nut. 2. Apply new engine oil to the oil filter feed pipe threads. cardiagn.com 3. Install the oil filter feed pipe in its s
  • Page 28Engine Oil Filter Feed Pipe Removal and Installation 1. Oil Filter - Remove 2. Oil Filter Feed Pipe - Remove 1. Oil Filter Feed Pipe - Install cardiagn.com 1. Install the two 20 x 1.5 mm nuts (A) onto the oil filter feed pipe. Hold the nut with a wrench, then tighten the other nut. 2. Apply new engi
  • Page 293. Install the oil filter feed pipe in its specified height range shown. 4. Remove the nuts from the oil filter feed pipe. 2. Oil Filter - Install cardiagn.com
  • Page 30Engine Oil Filter Removal and Installation Special Tool Required Image Description/Tool Number Oil Filter Wrench 07AAA-PLCA100 cardiagn.com 1. Vehicle - Lift 2. Engine Undercover Plate - Remove 3. Oil Filter - Remove 1. Remove the oil filter with the oil filter wrench.
  • Page 311. Oil Filter - Install 1. Inspect the oil filter to make sure the rubber seal is not stuck to the oil filter seating surface (A) of the oil pan. 2. Inspect the threads (B) and the rubber seal (C) on the new oil filter. 3. Clean the oil filter seating surface of the oil pan. 4. Apply a light coat of
  • Page 32cardiagn.co
  • Page 337. If four numbers or marks (1 to 4 or ▼ to▼▼▼▼) are printed around the outside of the filter, use the following procedure to tighten the filter. Spin the filter on until its seal lightly seats against the oil pan, and note which number or mark is at the bottom. Tighten the filter by turning it cloc
  • Page 34Engine Oil Filter Removal and Installation Special Tool Required Image Description/Tool Number Oil Filter Wrench 07AAA-PLCA100 cardiagn.com NOTE: Where icon is shown, click for further information. 1
  • Page 35cardiagn.com Detailed information, notes, and precautions 1. Engine Undercover Plate - Remove 2. Engine Oil Filter - Remove
  • Page 361. Remove the oil filter with the oil filter wrench. cardiagn.com NOTE: Where icon is shown, click for further information. 1
  • Page 37cardiagn.com Detailed information, notes, and precautions 1. Engine Oil Filter - Install
  • Page 381. Inspect the filter to make sure the rubber seal is not stuck to the oil filter seating surface of the oil pan. 2. Inspect the threads (A) and the rubber seal (B) on the new filter. 3. Clean the seat on the oil pan. cardiagn.com 4. Apply a light coat of new engine oil to the oil filter rubber seal
  • Page 397. If four numbers or marks (1 to 4 or ▼ to▼▼▼▼) are printed around the outside of the filter, use the following procedure to tighten the filter. Spin the filter on until its seal lightly seats against the oil pan, and note which number or mark is at the bottom. Tighten the filter by turning it cloc
  • Page 40Engine Oil Filter Removal and Installation Special Tool Required Image Description/Tool Number Oil Filter Wrench 07AAA-PLCA100 cardiagn.com 1. Vehicle - Lift 2. Engine Undercover Plate - Remove 3. Engine Oil Filter - Remove
  • Page 411. Remove the oil filter with the oil filter wrench. cardiagn.com 2. Inspect the filter to make sure the rubber seal is not stuck to the oil filter seating surface of the engine. 3. Inspect the threads (A) and the rubber seal (B) on the new filter. 4. Clean the seat on the oil pan. 1. Engine Oil Fil
  • Page 421. Apply a light coat of new engine oil to the oil filter rubber seal. NOTE: Use only filters with a built-in bypass system. 2. Install the oil filter by hand. 3. After the rubber seal seats, tighten the oil filter clockwise with the oil filter wrench. Tighten: 3/4 Turn Clockwise Tightening Torque:
  • Page 434. Maintenance Minder - Reset (With Maintenance Minder System) 1. USA models: If the Maintenance Minder required to replace the oil filter, reset the Maintenance Minder with the gauge (see "Resetting the Maintenance Minder"). 2. Canada models: If the Maintenance Minder required to replace the oil fi
  • Page 44Engine Oil Jet Inspection 1. Oil Jet - Remove 2. Oil Jet - Inspect Two nozzle type 1. Make sure that a 1.0 mm (1/32 in) diameter pin will go through the nozzle hole (A) (1.2 mm (0.047 in) diameter). NOTE: Replace the oil jet, if the nozzle is damaged or bent. 2. Make sure that a 1.8 mm (1/16 in) dia
  • Page 45Engine Oil Jet Inspection 1. Oil Jet - Remove 2. Oil Jet - Inspection 1. Inspect it as follows. Make sure that a 1.1 mm (1/32 in) diameter drill bit will go through the nozzle hole (A) (1.3 mm (0.051 in) diameter). Make sure that a 1.9 mm (1/16 in) diameter drill bit will go through the oil intake (
  • Page 46Engine Oil Jet Inspection 1. Oil Jet - Remove 2. Oil Jet - Inspection 1. Inspect it as follows. Make sure that a 1.0 mm (3/64 in) diameter drill bit will go through the nozzle hole (A) (1.2 mm (0.047 in) diameter). Make sure that a 1.0 mm (3/64 in) diameter drill bit will go through the oil intake (
  • Page 47Engine Oil Jet Removal and Installation 1. Crankshaft - Remove 2. Oil Jet - Remove cardiagn.com 3. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 48Engine Oil Jet Removal and Installation NOTE: How to read the torque specifications. Unless otherwise indicated, illustrations used in the procedure are for K20C2 engine. 1. Crankshaft - Remove 2. Oil Jet - Remove cardiagn.com 3. All Removed Parts - Install 1. Install the parts in the reverse order
  • Page 49Engine Oil Level Check 1. Engine Oil Level - Check 1. Park the vehicle on level ground, and start the engine. Hold the engine speed at 3,000 rpm with no load (M/T in neutral, CVT in P or N) until the cooling fan comes on, then turn off the engine, and wait more than 3 minutes. 2. Remove the dipstick
  • Page 50Engine Oil Level Check 1. Engine Oil Level - Check 1. Park the vehicle on level ground, and start the engine. Hold the engine speed at 3,000 rpm with no load (in neutral) until the radiator fan comes on, then turn off the engine, and wait more than 3 minutes. 2. Remove the dipstick, and wipe off the
  • Page 51Engine Oil Level Check 1. Engine Oil Level - Check 1. Park the vehicle on level ground, and start the engine. Hold the engine speed at 3,000 rpm with no load (M/T in neutral, CVT in P or N) until the radiator fan comes on, then turn off the engine, and wait more than 3 minutes. 2. Remove the dipstic
  • Page 52Engine Oil Pan Removal and Installation 1. Right Front Wheel - Remove 2. Engine Undercover Lid - Remove (With Engine Undercover Lid) 3. Engine Undercover - Remove 4. Engine Oil - Drain 5. Drive Belt - Remove cardiagn.com 6. Front Floor Brace - Remove (With Front Floor Brace) 7. Exhaust Pipe A - Remo
  • Page 5311. Torque Converter Cover/Clutch Cover - Remove cardiagn.com 1. Remove the torque converter cover (CVT) or the clutch cover (M/T) (A) and the transmission mounting bolts (B). 12.Torque Rod - Remove 13.Torque Rod Bracket - Remove 14.Intermediate Shaft Mounting Bolt - Remove
  • Page 5415.Oil Pan - Remove 1. Remove the oil pan mounting bolts. cardiagn.com
  • Page 552. Using a flat blade screwdriver, separate the oil pan from the engine block in the places shown. cardiagn.com 3. Remove the oil pan. NOTE: How to read the torque specifications. 1. Oil Pan - Install
  • Page 561. Apply liquid gasket to the engine block and the cam chain case mating surface of the oil pan, and to the inside edge of the threaded bolt holes. 2. Install the oil pan (A) with new O-rings (B). cardiagn.com 3. Tighten the oil pan mounting bolts in three steps. In the final step, torque all bolts,
  • Page 573. Torque Rod Bracket - Install cardiagn.com 4. Torque Rod - Install 5. Torque Converter Cover/Clutch Cover - Install 1. Install the torque converter cover (CVT) or the clutch cover (M/T) (A) and the transmission mounting bolts (B). 6. Oil Return Hose - Connect
  • Page 587. A/C Compressor - Install cardiagn.com 8. TWC Bracket - Install 9. Exhaust Pipe A - Install 10.Front Floor Brace - Install (With Front Floor Brace) 11. Drive Belt - Install 12.Engine Undercover - Install 13.Engine Undercover Lid - Install (With Engine Undercover Lid) 14.Right Front Wheel - Install
  • Page 59Engine Oil Pan Removal and Installation NOTE: Where icon is shown, click for further information. 1 cardiagn.com
  • Page 60cardiagn.co
  • Page 61Detailed information, notes, and precautions Replace 2 cardiagn.com Detailed information, notes, and precautions Replace
  • Page 62cardiagn.co
  • Page 631. Steering Joint - Disconnect NOTE: Hold the steering wheel with the steering wheel holder tool. 2. Engine Undercover - Remove NOTE: Remove the necessary part(s). 3. Engine Oil - Drain 4. Exhaust Pipe A - Remove 5. TWC Bracket - Remove cardiagn.com 6. Drive Belt - Remove 7. A/C Compressor - Move NO
  • Page 641. Support the engine with a transmission jack and a wood block under the oil pan. 13.Torque Rod and Torque Rod Bracket - Remove 14.Transmission Jack - Remove 15.CKP Sensor Cover - Remove 16.Front Brace - Remove 17.Front Subframe - Move cardiagn.com 1. Support the front subframe with a transmission
  • Page 652. Using a flat blade screwdriver, separate the oil pan from the lower block in the places shown. cardiagn.com NOTE: Where icon is shown, click for further information. 1
  • Page 66cardiagn.com Detailed information, notes, and precautions Torque: N·m (kgf·m, lbf·ft) Replace 1. Oil Pan - Install 1. Apply new engine oil to the inside edge of the oil return hose.
  • Page 672. Apply liquid gasket to the lower block and the cam chain case mating surface of the oil pan, and to the inside edge of the threaded bolt holes. 3. Tighten the bolts in three steps. In the final step, torque all bolts, in sequence, to the specified torque. Wipe off the excess liquid gasket on the
  • Page 6813.Drive Belt - Install 14.TWC Bracket - Install 15.Exhaust Pipe A - Install 16.Engine Undercover - Install 17.Steering Joint - Connect cardiagn.com 18.Engine Oil - Refill 19.Wheel Alignment - Check
  • Page 69Engine Oil Pan Removal and Installation 1. Engine Undercover Lid - Remove 2. Engine Undercover - Remove 3. Engine Oil - Drain 4. Exhaust Pipe A - Remove 5. TWC Bracket - Remove cardiagn.com 6. Drive Belt - Remove 7. A/C Compressor - Move (With A/C) NOTE: Do not disconnect the suction hose and the di
  • Page 701. Remove the clutch cover (M/T) or the torque converter cover (CVT) (A) and the transmission mounting bolts (B). 10.Torque Rod - Remove cardiagn.com 11. Torque Rod Bracket - Remove 12.Lower Arm Mounting Bolt - Remove 13.Middle Stiffener Mounting Bolt - Remove
  • Page 7114.Front Subframe Rear Stay Mounting Bolt/Nut - Remove cardiagn.com 15.Front Subframe - Move
  • Page 72Rear side 1. Loosen the subframe mounting bolts (A) from the front subframe (B) on rear side, so they are about 30 mm (1.18 in) from the mounting surface. cardiagn.com Front side 2. Loosen the subframe mounting bolts (A) from the front subframe (B) on front side, so they are about 30 mm (1.18 in) fr
  • Page 731. Remove the oil pan mounting bolts. 2. Using a flat blade screwdriver, separate the oil pan from the lower block in the places shown. cardiagn.com 3. Remove the oil pan.
  • Page 741. Oil Pan - Install 1. Apply liquid gasket to the lower block and the cam chain case mating surface of the oil pan, and to the inside edge of the threaded bolt holes. 2. Install the oil pan (A) with a new O-ring (B). cardiagn.com 3. Tighten the bolts in three steps. In the final step, torque all bo
  • Page 755. Transmission Jack - Remove cardiagn.com 6. Torque Rod Bracket - Install 7. Torque Rod - Install 8. Clutch Cover/Torque Converter Cover - Install 1. Install the clutch cover (M/T) or the torque converter cover (CVT) (A) and the transmission mounting bolts (B).
  • Page 769. Drive Belt Idler Pulley Base - Install (Without A/C) 10.A/C Compressor - Install (With A/C) 11. Drive Belt - Install 12.TWC Bracket - Install 13.Exhaust Pipe A - Install 14.Engine Undercover - Install cardiagn.com 15.Engine Undercover Lid - Install 16.Engine Oil - Refill 17.Wheel Alignment - Chec
  • Page 77Engine Oil Pressure Switch Removal and Installation 1. Right Front Wheel - Remove 2. Engine Undercover Lid - Remove (With Engine Undercover Lid) 3. Engine Undercover - Remove 4. Drive Belt - Remove cardiagn.com 5. A/C Compressor - Move NOTE: Do not disconnect the suction hose and the discharge hose.
  • Page 78cardiagn.co
  • Page 791. Oil Pressure Switch - Install 1. Apply liquid gasket (P/N 08718-0003, 08718-0004, or 08718-0009) to the oil pressure switch threads. Install the component within 5 minutes of applying the liquid gasket. NOTE: Using too much liquid gasket may cause liquid gasket to enter the oil passage or the end
  • Page 80Engine Oil Pressure Switch Removal and Installation 1. Oil Pressure Switch - Remove 1. Disconnect the connector (A). 2. Remove the oil pressure switch (B). 3. Remove any old liquid gasket from the oil pressure switch and the switch mounting hole. cardiagn.com 1. Oil Pressure Switch - Install
  • Page 811. Apply liquid gasket (P/N 08718-0003, 08718-0004, or 08718- 0009) to the oil pressure switch threads. Install the component within 5 minutes of applying the liquid gasket. NOTE: Using too much liquid gasket may cause liquid gasket to enter the oil passage or the end of the oil pressure switch. If
  • Page 82Engine Oil Pressure Switch Test 1. Right Front Wheel - Remove 2. Engine Undercover - Remove 3. Oil Pressure Switch - Test 1. Disconnect the connector (A). 2. Check for continuity between the oil pressure switch terminal (B) and the engine (ground). There should be continuity with the engine stopped.
  • Page 83Engine Oil Pressure Switch Test 1. Oil Pressure Switch - Test 1. Disconnect the connector (A). 2. Check for continuity between the oil pressure switch terminal (B) and the engine (ground). There should be continuity with the engine stopped. There should be no continuity with the engine running. 3. C
  • Page 84Engine Oil Pressure Test Special Tool Required Image Description/Tool Number Oil Pressure Gauge Attachment PT1/8 07510-MA70000 cardiagn.com Oil Pressure Gauge 07506-3000001 If the low oil pressure indicator stays on with the engine running, check the engine oil level. If the oil level is correct, go
  • Page 851. Install the oil pressure gauge attachment PT1/8 and the oil pressure gauge to the oil pressure switch mounting hole. cardiagn.com 3. A/C Compressor - Install 4. Drive Belt - Install 5. Engine Oil Pressure - Test 1. Start the engine. Shut it off immediately if the gauge registers no oil pressure.
  • Page 861. Install the parts in the reverse order of removal. cardiagn.com
  • Page 87Engine Oil Pressure Test Special Tool Required Image Description/Tool Number Oil Pressure Hose 07ZAJ-S5AA200 cardiagn.com Pressure Gauge Adapter 07NAJ-P07010A A/T Pressure Adapter 07MAJ-PY40120
  • Page 88Image Description/Tool Number A/T Pressure Test Hose 07AAJ-PY4A100 A/T Low Pressure Gauge w/Panel 07406-0070301 cardiagn.com NOTE: If the low oil pressure indicator stays on with the engine running, check the engine oil level. If the oil level is correct: 1. Rocker Arm Oil Pressure Sensor - Remove 2
  • Page 89cardiagn.com 2. Start the engine. Shut it off immediately if the gauge registers no oil pressure. Repair the problem before continuing. 3. Allow the engine to reach operating temperature (fan comes on at least twice). The pressure should be: Engine Oil Temperature: 176 °F (80 °C) Engine Oil Pressure
  • Page 90Engine Oil Pressure Test If the low oil pressure indicator stays on with the engine running, check the engine oil level. If the oil level is correct: 1. Oil Pressure Switch - Remove 2. Engine Oil Pressure - Test 1. Install the oil pressure gauge (A) as shown. cardiagn.com 2. Start the engine. Shut i
  • Page 91cardiagn.co
  • Page 924. All Removed Parts - Install 1. Install the parts in the reverse order of removal. cardiagn.com
  • Page 93Engine Oil Pump Chain Removal and Installation Special Tool Required Image Description/Tool Number Universal Lifting Eyelet 07AAK-SNAA120 cardiagn.com Engine Support Hanger, A and Reds AAR-T1256* *: Available through the Honda Tool and Equipment Program 888-424-6857. 1
  • Page 94cardiagn.com 1. Cam Chain - Remove 2. Engine Support Hanger and Universal Lifting Eyelet - Install
  • Page 95NOTE: Be careful when working around the windshield. Be careful not to damage the hood opener cable when installing the engine support hanger at the front bulkhead. 1. Remove the front damper caps. 2. Install the universal lifting eyelet with a commercially available spacer (A) (about 50 mm (1.97 in
  • Page 96cardiagn.com Detailed information, notes, and precautions 1. Crankshaft Sprocket - Install 2. Oil Pump Chain - Install
  • Page 971. Set the crankshaft to top dead center (TDC). Align the TDC mark (A) on the crankshaft sprocket with the pointer (B) on the engine block. 2. Install the oil pump chain. NOTE: These marks (C) shall be used in product process only and not used for maintenance purpose. There is no need to line up the
  • Page 986. Cam Chain - Install cardiagn.com
  • Page 99Engine Oil Pump Chain Removal and Installation Special Tool Required Image Description/Tool Number Universal Lifting Eyelet 07AAK-SNAA120 cardiagn.com Engine Support Hanger, A and Reds AAR-T1256* *: Available through the Honda Tool and Equipment Program 888-424-6857. 1. Alternator Mounting Bolt - Re
  • Page 1002. Cam Chain - Remove cardiagn.com 3. Engine Support Hanger and Universal Lifting Eyelet - Install NOTE: Be careful when working around the windshield. Be careful not to damage the hood opener cable when installing the engine support hanger at the front bulkhead. 1. Remove the front damper caps.
  • Page 101cardiagn.com 2. Attach the universal lifting eyelet to the alternator. 3. Install the engine support hanger onto the vehicle as shown. 4. Attach the hook to the slotted hole in the universal lifting eyelet. 5. Tighten the wing nut (A) by hand, and lift and support the engine/transmission. 4. Oil Pum
  • Page 102cardiagn.com NOTE: These marks (A) shall be used in product process only and not used for maintenance purpose. There is no need to line up the marks as it has no effect on the engine operation. 1. Oil Pump Chain - Install
  • Page 1031. Install the oil pump chain (A). 2. Oil Pump - Install cardiagn.com 3. Engine - Support 1. Lift and support the engine with a jack and a wood block under the oil pan. 4. Engine Support Hanger and Universal Lifting Eyelet - Remove 5. Cam Chain - Install 6. Alternator Mounting Bolt - Install
  • Page 104cardiagn.co
  • Page 105Engine Oil Pump Overhaul NOTE: Do not disassemble the oil pump except for the shown parts. 1. Oil Pump - Exploded View Exploded View cardiagn.com
  • Page 106Engine Oil Pump Overhaul NOTE: Where icon is shown, click for further information. Do not disassemble the oil pump except for the shown parts. 1 cardiagn.com
  • Page 107Detailed information, notes, and precautions cardiagn.com
  • Page 108Torque: N·m (kgf·m, lbf·ft) 1. Relief Valve - Remove NOTE: Valve must slide freely in the housing bore. Replace if scored. 2. All Removed Parts - Install 1. Install the parts in the reverse order of removal. cardiagn.com
  • Page 109Engine Oil Pump Overhaul NOTE: Do not disassemble the oil pump except for the shown parts. 1. Oil Pump - Exploded View Exploded View cardiagn.com
  • Page 110Engine Oil Pump Removal and Installation Special Tool Required Image Description/Tool Number Engine Support Hanger, A and Reds AAR-T1256* cardiagn.com Universal Lifting Eyelet 07AAK-SNAA120 *: Available through the Honda Tool and Equipment Program 888-424-6857. 1. Front Grille Cover - Remove 2. Air
  • Page 1115. Cam Chain - Remove 6. Cam Chain Drive Sprocket - Remove 1. Remove the key (A) and the cam chain drive sprocket (B). NOTE: Check the direction of the key. When the key is installed, install the key as same direction of the original one. cardiagn.com 7. Universal Lifting Eyelet - Install 8. Engine
  • Page 112cardiagn.com 2. Install the engine support hanger onto the vehicle as shown. 3. Attach the hook (A) to the slotted hole in the universal lifting eyelet. 4. Tighten the wing nut (B) by hand, and lift and support the engine. 9. Oil Pan - Remove 10.Oil Pump - Remove
  • Page 1131. Remove the oil strainer (A) and the oil pump (B). cardiagn.com 1. Oil Pump - Install 1. Install the oil pump (A). 2. Install the oil strainer (B) with a new O-ring (C). 2. Oil Pan - Install 3. Engine - Support
  • Page 1141. Lift and support the engine with a jack and a wood block under the oil pan. 4. Engine Support Hanger and Universal Lifting Eyelet - Remove 5. Cam Chain Drive Sprocket - Install 1. Install the cam chain drive sprocket (A) and the key (B). cardiagn.com 6. Cam Chain - Install 7. Turbocharger Joint a
  • Page 115Engine Oil Pump Removal and Installation NOTE: Where icon is shown, click for further information. 1 cardiagn.com
  • Page 116cardiagn.co
  • Page 117Detailed information, notes, and precautions Torque: N·m (kgf·m, lbf·ft) Replace 1. Oil Pan - Remove 2. Oil Strainer - Remove 3. Oil Pump Chain Tensioner - Remove 4. Oil Pump - Remove Note for installation cardiagn.com These marks (A) shall be used in product process only and not used for maintenanc
  • Page 118Engine Oil Pump Removal and Installation 1. Oil Pan - Remove 2. Oil Pump - Remove 1. Remove the oil strainer (A). 2. Remove the oil pump chain tensioner (B). 3. Remove the oil pump (C). cardiagn.com 3. All Removed Parts - Install
  • Page 1191. Install the parts in the reverse order of removal. NOTE: These marks (A) shall be used in product process only and not used for maintenance purpose. There is no need to line up the marks as it has no effect on the engine operation. cardiagn.com
  • Page 120Engine Oil Replacement NOTE: How to read the torque specifications. 1. Engine - Warm Up 1. Start the engine. Hold the engine speed at 3,000 rpm with no load (M/T in neutral, CVT in P or N) until the cooling fan comes on, then turn off the engine. 2. Vehicle - Lift 3. Engine Undercover Plate - Remove
  • Page 1211. Remove the drain bolt (A), and drain the engine oil. 2. Reinstall the drain bolt with a new washer (B) and torque to specification. 5. Engine Oil - Refill cardiagn.com 1. Refill the engine with the recommended engine oil. Capacity At Oil Change: 3.2 L (3.4 US qt) At Oil Change including Filter: 3
  • Page 1228. Maintenance Minder - Reset (With Maintenance Minder System) cardiagn.com 1. If the Maintenance Minder required to replace the engine oil, reset the Maintenance Minder with the gauge (see "Resetting the Maintenance Minder"). If the Maintenance Minder did not require to replace the engine oil, rese
  • Page 123Engine Oil Replacement NOTE: How to read the torque specifications. 1. Engine - Warm Up 1. Allow the engine to reach operating temperature (fan comes on at least twice). 2. Vehicle - Lift 3. Engine Undercover Plate - Remove cardiagn.com 4. Engine Oil - Drain
  • Page 1241. Remove the drain bolt (A), and drain the engine oil. 2. Reinstall the drain bolt with a new washer (B) and torque to specification. NOTE: Do not overtighten. cardiagn.com 5. Engine Oil - Refill 1. Refill the engine with the recommended engine oil. Capacity At Oil Change: 5.0 L (5.3 US qt) At Oil
  • Page 1258. Maintenance Minder - Reset (With Maintenance Minder System) cardiagn.com 1. If the Maintenance Minder required to replace the engine oil, reset the Maintenance Minder with the gauge (see "Resetting the Maintenance Minder"). If the Maintenance Minder did not require to replace the engine oil, rese
  • Page 126Engine Oil Replacement 1. Engine - Warm Up 1. Allow the engine to reach operating temperature (fan comes on at least twice). 2. Vehicle - Lift 3. Engine Undercover Plate - Remove cardiagn.com 4. Engine Oil - Drain
  • Page 1271. Remove the drain bolt (A), and drain the engine oil. 2. Reinstall the drain bolt with a new washer (B) and torque to specification. cardiagn.com 5. Engine Oil - Refill 1. Refill the engine with the recommended engine oil. Capacity At Oil Change: 4.0 L (4.2 US qt) At Oil Change including Filter: 4
  • Page 1288. Maintenance Minder - Reset (With Maintenance Minder System) cardiagn.com 1. If the Maintenance Minder required to replace the engine oil, reset the Maintenance Minder with the gauge (see "Resetting the Maintenance Minder"). If the Maintenance Minder did not require to replace the engine oil, rese
  • Page 129Engine Oil/Air Separator Removal and Installation NOTE: How to read the torque specifications. Unless otherwise indicated, illustrations used in the procedure are for K20C2 engine. 1. Flywheel - Remove (M/T) 2. Drive Plate - Remove (CVT) 3. Oil/Air Separator - Remove cardiagn.com 4. All Removed Part