Honda CIVIC 10G 2016 Seat System Page 1

Seats Component Location Index
Front
Rear (2/4-door)
Seats Component Location Index 9643 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/...
1 of 3 1/28/2019 5:47 AM
cardiagn.com

Contents Summary of Seat System

  • Page 1Seats Component Location Index Front cardiagn.com Rear (2/4-door)
  • Page 2Rear (5-door) cardiagn.com
  • Page 3cardiagn.co
  • Page 4Seat Heaters Circuit Diagram Front Seat Heater cardiagn.com Rear Seat Heater
  • Page 5cardiagn.co
  • Page 6cardiagn.co
  • Page 7Seat Heaters Circuit Diagram Front Seat Heater cardiagn.com
  • Page 8Seat Heaters Circuit Diagram Front Seat Heater cardiagn.com Rear Seat Heater
  • Page 9cardiagn.co
  • Page 10cardiagn.co
  • Page 11Seat Heaters Circuit Diagram cardiagn.com
  • Page 12Seat Heaters Component Location Index Driver's Seat cardiagn.com Front Passenger's Seat
  • Page 13Rear Seat (With Rear Seat Heater) cardiagn.com
  • Page 14cardiagn.co
  • Page 15cardiagn.com With Rear Seat Heater
  • Page 16cardiagn.co
  • Page 17Seat Heaters System Description - Components Seat Heater Switches The front seat heater switches are installed in the climate control panel, and the rear seat heater switches are installed the rear of the center console. Thermostat and Breaker (Rear Seat) The seat cushion heater has a thermostat and
  • Page 18Seat Heaters System Description - Control/Function Heater Control Front Seat Heaters The front seat heater control unit sets the seat heater to High/Mid/Low or OFF based on the seat heater switch signals received from the climate control unit via the B-CAN. The front seat heater control unit monitor
  • Page 19The seat heater temperature is controlled by breaker ON and OFF condition. cardiagn.com ON OFF Front Seat Cushion 113 ― 131 °F (45 ― 55 °C) 167 ― 185 °F (75 ― 85 °C) Breaker
  • Page 20Seat Heaters System Description - Failsafe Function Thermistor Circuit Open Failure When the seat heater control unit detects a thermistor wire break, it stops the heater output 90 seconds after detection and turns off the seat heater switch indicator. Thermistor Circuit Short Failure When the seat
  • Page 21Seat Heaters System Description - System Diagram For locations of each component on the vehicle, refer to the Component Location Index cardiagn.com
  • Page 22Driver's Power Seat Adjustment Switch Removal and Installation 1. Driver's Seat Recline Cover - Remove NOTE: If removing the driver's seat recline cover, you do not need to remove the driver's seat. 2. Driver's Power Seat Adjustment Switch - Remove 1. Remove the driver's power seat adjustment switch
  • Page 23Driver's Power Seat Adjustment Switch Test 1. Driver's Seat Recline Cover - Remove NOTE: If removing the driver's seat recline cover, you do not need to remove the driver's seat. 2. Driver's Power Seat Adjustment Switch - Test 1. Check for continuity between the terminals in each switch position acc
  • Page 24cardiagn.co
  • Page 251. Install the parts in the reverse order of removal. cardiagn.com
  • Page 26Driver's Power Seat Motor Test SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Driver's Seat Recline Cover - Remove NOTE: If removing the driver's seat recline cover, you do not need to remove the driv
  • Page 27cardiagn.com 3. Remove the driver's seat-back cover/pad as needed. 4. Remove the driver's seat cushion cover/pad (A) as needed. 5. Disconnect the connector(s) (B).
  • Page 28cardiagn.co
  • Page 296. Test each motor in each direction by connecting power and ground according to the table. When the motor stops running, disconnect 12 volt battery power immediately. 7. If the motor does not run or fails to run smoothly, replace: NOTE: All motors are part of the seat frame. Front up-down motor/sea
  • Page 30Driver's Seat Position Sensor Operation Check NOTE: Check the driver's seat position sensor operation after the driver's seat position sensor replacement or removal. 1. HDS - Connect 2. Driver's Seat Position Sensor - Operation Check 1. Make sure the driver's seat is in the full forward position. 2.
  • Page 31Driver's Seat Position Sensor Removal and Installation SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. NOTE: Do not turn the vehicle to the ON mode, while removing or installing the driver's seat position
  • Page 32cardiagn.co
  • Page 335. SRS Operation - Confirm 1. Turn the vehicle to the ON mode, and check that the SRS indicator comes on for about 6 seconds and then goes off. cardiagn.com
  • Page 34Front Passenger's Power Seat Adjustment Switch Removal and Installation 1. Front Passenger's Seat Recline Cover - Remove NOTE: If removing the front passenger's seat recline cover, you do not need to remove the front passenger's seat. 2. Front Passenger's Power Seat Adjustment Switch - Remove 1. Rem
  • Page 35Front Passenger's Power Seat Adjustment Switch Test 1. Front Passenger's Seat Recline Cover - Remove NOTE: If removing the front passenger's seat recline cover, you do not need to remove the front passenger's seat. 2. Front Passenger's Power Seat Adjustment Switch - Test 1. Check for continuity betw
  • Page 36Front Passenger's Power Seat Motor Test SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Passenger's Seat Recline Cover - Remove NOTE: If removing the front passenger's seat recline cover, you do
  • Page 37cardiagn.co
  • Page 383. Remove the seat-back cover/pad as needed. 4. Disconnect the connector(s) (A). cardiagn.com Slide motor 5. Test each motor by connecting power and ground according to the table. When the motor stops running, disconnect 12 volt battery power immediately. 6. If the motor does not run or fails to run
  • Page 39Slide motor/seat frame Recline motor/seat frame If the motor runs smoothly, replace the front passenger's seat wire harness. Recline motor 3. All Removed Parts - Install cardiagn.com 1. Install the parts in the reverse order of removal.
  • Page 40Front Seat Cushion Cover Removal and Installation SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat Recline Cover - Remove 2. Front Seat Cushion Cover/Pad - Remove With Seat Heater 1. For some
  • Page 41cardiagn.co
  • Page 42Except Type-R 2. Release the hook strips (A). cardiagn.com Type-R
  • Page 43Driver's Seat (Except Type-R) 3. Release the hook strips (A). 4. Driver's seat (except Type-R): Remove the clip (B). Passenger's Seat (Except Type-R) cardiagn.com Type-R
  • Page 44cardiagn.co
  • Page 455. Remove the seat cushion cover/pad (A). 3. Front Seat Cushion Cover - Remove Except Type-R 1. Release the upholstery rings (A) and the hook and loop fasteners (B), then remove the seat cushion cover (C). cardiagn.com
  • Page 46Type-R cardiagn.com 4. All Removed Parts - Install 1. Install the parts in the reverse order of removal. NOTE: Replace all of the upholstery rings (A) fastening the seat cushion cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D).
  • Page 47Front Seat Frame Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat-Back Cover/Pad - Remove 2. Front Seat Cushion Cover/Pad - Remove 3. Front Seat Belt Buckle - R
  • Page 48Right side cardiagn.com 5. Front Seat Rear Foot Cover - Remove 6. Recline Inner/Outer Cover - Remove
  • Page 497. Front Seat Side Airbag Holder - Remove cardiagn.com 8. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 50Front Seat Frame Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat-Back Cover/Pad - Remove 2. Front Seat Cushion Cover/Pad - Remove 3. Front Seat Belt Buckle - R
  • Page 51Right side cardiagn.com 5. Front Seat Rear Foot Cover - Remove 6. Recline Inner/Outer Cover - Remove
  • Page 52Driver's seat Passenger's seat 7. Front Seat Side Airbag Holder - Remove cardiagn.com 8. All Removed Parts - Install
  • Page 53cardiagn.co
  • Page 541. Install the parts in the reverse order of removal. cardiagn.com
  • Page 55Front Seat Recline Cover Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat - Remove 2. Walk-In Knob - Remove (Passenger's Seat) cardiagn.com 3. Height Adjuster H
  • Page 561. Remove the cap (A). 2. Remove the height adjuster handle (B). cardiagn.com 4. Front Seat Recline Cover - Remove Driver's seat 1. Remove the front seat recline knob (A). 2. Remove the front seat recline cover (B).
  • Page 57Passenger's seat cardiagn.com 5. Front Seat Center Cover - Remove Driver's seat
  • Page 58Passenger's seat cardiagn.com 6. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 59Front Seat Recline Cover Removal and Installation 1. Front Seat - Remove 2. Height Adjuster Handle - Remove (Driver's Manual Seat) 1. Remove the cap (A). 2. Remove the height adjuster handle (B). 3. Front Seat Recline Cover - Remove cardiagn.com Power seat 1. Manual seat: Remove the front seat recli
  • Page 60Driver's manual seat Passenger's manual seat cardiagn.com 4. Front Seat Center Cover - Remove
  • Page 61Driver's seat Passenger's seat cardiagn.com 5. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 62Front Seat Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. 12 Volt Battery Terminal - Disconnect NOTE: Wait at least 3 minutes before starting work. 2. Front Seat Rear In
  • Page 63Front side cardiagn.com 4. Front Seat - Remove 1. Lift up the front seat, then disconnect the connectors (A) and remove the harness clips (B). 2. Remove the head restraint. 3. With the help of an assistant, carefully remove the front seat (A) through the front door opening. 5. All Removed Parts - In
  • Page 64Front side 1. Install the parts in the reverse order of removal. NOTE: Tighten the bolts by hand first, then tighten them to the specified torque in the sequence shown. cardiagn.com Rear side 6. Front Passenger's Weight Sensor - Operation Check
  • Page 65Front Seat Removal and Installation SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. NOTE: How to read the torque specifications. 1. Front Seat Mounting Bolts - Remove Rear side cardiagn.com Front side 2.
  • Page 66cardiagn.co
  • Page 67NOTE: Wait at least 3 minutes before starting work. 3. Front Seat - Remove 1. Lift up the front seat, then disconnect the connectors (A) and remove the harness clips (B). cardiagn.com 2. Remove the head restraint. 3. With the help of an assistant, carefully remove the front seat (A) through the fron
  • Page 68Front side 1. Install the parts in the reverse order of removal. NOTE: Tighten the bolts by hand first, then tighten them to the specified torque in the sequence shown. Rear side cardiagn.com 5. Front Passenger's Weight Sensor - Operation Check How to Access the Front Seat Rear Mounting Bolts for th
  • Page 691. Adjust the front seat cushion (A) to the full tilt up position. 2. Remove the recline cover (B) as needed. 3. Disconnect the connector (C). 4. Remove the cushion cover/pad (A) as needed. cardiagn.com
  • Page 705. Remove the harness clips (A). 6. Remove the cushion spring (B) as needed. cardiagn.com 7. Remove the slide motor cover (A). 8. Disconnect the connector (B). 9. Remove the bolts (C).
  • Page 7110. Release the cable housing (A) from the hooks (B). 11. Disconnect both slide motor cables (C) from both transmissions (D). 12. Disconnect the slide motor cable from the slide motor (E). NOTE: Be careful not to kink the cable. cardiagn.com 13. Remove the slide motor bracket assembly (A).
  • Page 72Inboard rail 14. Connect the one side of the slide motor cable (A) to the drill (B), and the other side of the cable to the transmission (C). 15. Operate the drill to the slide rail, alternating between the inboard and the outboard rails, reverse the drill directions needed for each rail. 16. Remove
  • Page 73Front Seat Slide Lever Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat - Remove 2. Front Seat Slide Lever - Remove cardiagn.com 3. All Removed Parts - Install
  • Page 74Front Seat-Back Cover Removal and Installation SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat - Remove 2. Front Seat-Back Cover/Pad - Remove 1. From under the seat cushion, remove these ite
  • Page 752. Release the hook strip (A). 3. Unzip the seat-back cover (B). cardiagn.com 4. Release the hook strips (A). 5. With seat heater: Remove the harness holder (B). 6. Without cloth reinforcement type: Remove the side airbag.
  • Page 767. Height adjustable head restraint: Remove the head restraint guides (A). cardiagn.com 8. For some models: Remove the clips (A). 9. Remove the seat-back cover/pad (B). 3. Front Seat-Back Cover - Remove
  • Page 77Height Adjustable Head Restraint 1. Remove the upholstery rings (A) securing the seat-back cover (B). cardiagn.com Fixed Head Restraint 4. All Removed Parts - Install
  • Page 781. Install the parts in the reverse order of removal. NOTE: Replace all of the upholstery rings (A) fastening the seat-back cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D). cardiagn.com
  • Page 79Front Seat-Back Cover Removal and Installation SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. 1. Front Seat-Back Panel - Remove 1. Turn over the front seat-back undercover (A). cardiagn.com
  • Page 802. Release the hook strip (A). cardiagn.com 3. Release the hooks (A).
  • Page 814. Release the hook strips (A). cardiagn.com 5. Remove the front seat-back panel (A).
  • Page 826. If necessary, remove the front seat-back front trim covers (A). 2. Front Seat - Remove cardiagn.com 3. Front Seat-Back Cover/Pad - Remove 1. Remove the harness clips (A).
  • Page 832. Release the hook strips (A). 3. Remove the side airbag. cardiagn.com
  • Page 844. Remove the clips (A). 5. Remove the seat-back cover/pad (B). cardiagn.com 4. Front Seat-Back Cover - Remove 1. Release the upholstery rings (A) and the hook and loop fasteners (B), then remove the seat-back cover (C). 5. All Removed Parts - Install
  • Page 851. Install the parts in the reverse order of removal. NOTE: Replace all of the upholstery rings (A) fastening the seat-back cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D). cardiagn.com
  • Page 86Power Seats Circuit Diagram Driver's Power Seat cardiagn.com Front Passenger's Power Seat
  • Page 87cardiagn.co
  • Page 88Power Seats Component Location Index Driver's Seat cardiagn.com Front Passenger's Seat
  • Page 89cardiagn.co
  • Page 90Rear Seat Armrest Beverage Holder Removal and Installation 1. Rear Seat Armrest Beverage Holder - Remove 1. Release the hooks (A) of the rear seat armrest beverage holder (B) from the rod (C) with the appropriate trim tool. 2. Release the hooks (A) of the rear seat armrest beverage holder (B) from t
  • Page 91Rear Seat Cushion Cover Removal and Installation 1. Rear Seat Cushion - Remove 2. Rear Seat Cushion Cover - Remove 1. From the back of the rear seat cushion (A), release the upholstery rings (B), then fold back the rear seat cushion cover. cardiagn.com 2. Pull back the edge of the seat cushion cover
  • Page 92Rear Seat Cushion Cover Removal and Installation 1. Rear Seat Trim - Remove (Type-R) 2. Rear Seat Cushion - Remove 3. Rear Seat Cushion Cover - Remove 1. With rear seat heater: Disconnect the connector (A). 2. With rear seat heater: From the back of the seat cushion, pass the seat heater harness (B)
  • Page 93Type-R 4. All Removed Parts - Install 1. Install the parts in the reverse order of removal. NOTE: Replace all of the upholstery rings (A) fastening the seat cushion cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D). cardiagn.com
  • Page 94Rear Seat Removal and Installation NOTE: How to read the torque specifications. Rear Right Seat-Back (2/4-door, Split Fold Down Seat) 1. Rear Right Seat-Back - Remove 1. Fold down the rear right seat-back (A). 2. Turn over the rear right seat-back covers (B), then remove the bolts (C). 3. Remove the
  • Page 953. All Removed Parts - Install 1. Install the parts in the reverse order of removal. Rear Right Seat-Back (5-door, Split Fold Down Seat) 1. Rear Right Seat-Back - Remove 1. Fold down the rear right seat-back (A). 2. Turn over the rear right seat-back cover (B), then remove the bolts (C). 3. Remove t
  • Page 96cardiagn.com 3. All Removed Parts - Install 1. Install the parts in the reverse order of removal. Rear Left Seat-Back (2/4-door, Split Fold Down Seat) 1. Rear Right Seat-Back - Remove 2. Rear Left Seat-Back - Remove
  • Page 971. Pull out the center seat belt (A) through the slit in the center seat belt guide (B). 2. Fold down the rear left seat-back (C). 3. Turn over the rear left seat-back cover (D), then remove the bolts (E, F). 4. Remove the rear left seat-back. cardiagn.com 3. Rear Seat Pivot Bracket - Remove 4. Coll
  • Page 985. All Removed Parts - Install 1. Install the parts in the reverse order of removal. Rear Left Seat-Back (5-door, Split Fold Down Seat) cardiagn.com 1. Rear Right Seat-Back - Remove 2. Rear Center Seat Belt Lower Anchor Bolt - Remove 3. Rear Left Seat-Back - Remove 1. Fold down the rear left seat-ba
  • Page 994. Rear Seat Pivot Bracket - Remove cardiagn.com 5. Collar - Remove (Split Fold Down Left Seat) 6. All Removed Parts - Install 1. Install the parts in the reverse order of removal. Rear Seat-Back (Fold Down Seat) 1. Rear Seat-Back - Remove
  • Page 1001. Pull out the center seat belt (A) through the slit in the center seat belt guide (B). 2. Fold down the rear seat-back (C). 3. Turn over the rear seat-back cover (D), then remove the bolts (E). 4. Remove the rear seat-back. cardiagn.com 2. Rear Seat Pivot Bracket - Remove 3. All Removed Parts - In
  • Page 1011. Remove the bolt (A). cardiagn.com 2. While pushing down on the seat cushion (A), pull the seat hook handles (B) to release the hooks (C). 3. Remove the rear seat cushion. 4. With rear seat heater: Disconnect the connector (D). 2. All Removed Parts - Install 1. Install the parts in the reverse ord
  • Page 102Rear Seat Trim Removal and Installation 1. Rear Seat Trim - Remove cardiagn.com 2. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 103Rear Seat-Back Cover Removal and Installation 2/4-door 1. Rear Seat Armrest - Remove (For Some Models) 2. Rear Seat-Back - Remove 3. Center Seat Belt Guide - Remove cardiagn.com 4. Armrest Back Panel - Remove (For Some Models)
  • Page 104cardiagn.com 5. Rear Seat-Back Cover/Pad - Remove Split Fold Down Seat 1. Split fold down seat: Remove the clips (A). 2. Release the hook strips (B).
  • Page 105Fold Down Seat cardiagn.com Split Fold Down Seat 3. Release the hook strips (A). Fold Down Seat
  • Page 1064. Remove the seat-back frame (A), then remove the rear seat-back cover/pad (B). 6. Rear Seat-Back Cover - Remove cardiagn.com Left Split Fold Down Seat 1. Release the upholstery rings (A), then remove the seat-back cover (B).
  • Page 107Right Split Fold Down Seat cardiagn.com Fold Down Seat 7. All Removed Parts - Install
  • Page 1081. Install the parts in the reverse order of removal. NOTE: Replace all of the upholstery rings (A) fastening the seat-back cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D). 5-door 1. Rear Seat-Back - Remove 2. Rear Seat-Back Latch Cover - Remove c
  • Page 1094. Rear Seat Lock Trim - Remove cardiagn.com 5. Rear Center Seat Belt Center Webbing Guide - Remove
  • Page 110cardiagn.com 6. Rear Seat-Back Cover/Pad - Remove 1. Unzip the seat-back cover (A). 2. Release the hook strips (B).
  • Page 1113. Remove the seat-back frame (A), then remove the rear seat-back cover/pad (B). 7. Rear Seat-Back Cover - Remove cardiagn.com 1. Release the upholstery rings (A), then remove the seat-back cover (B). 8. All Removed Parts - Install
  • Page 1121. Install the parts in the reverse order of removal. NOTE: Replace all of the upholstery rings (A) fastening the seat-back cover (B) to the pad wires (C) with new ones using commercially available upholstery ring pliers (D). cardiagn.com
  • Page 113Rear Seat-Back Latch Removal and Installation NOTE: How to read the torque specifications. 2/4-door 1. Rear Shelf - Remove 2. Rear Seat-Back Release Lever/Cable - Remove 3. Rear Seat-Back Latch - Remove cardiagn.com 4. Rear Seat-Back Cover/Pad - Remove 5. All Removed Parts - Install 1. Install the p
  • Page 1142. Rear Seat-Back Latch - Remove cardiagn.com 3. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 115Rear Seat-Back Release Lever/Cable Removal and Installation 1. Rear Seat-Back Release Lever/Cable - Remove Lever cardiagn.com
  • Page 116Cable cardiagn.com 2. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 117Rear Seat-Back Striker Removal and Installation NOTE: How to read the torque specifications. 1. Rear Side Trim Panel - Remove 2. Rear Seat-Back Striker - Remove cardiagn.com 3. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 118Seat Heater Replacement SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. Front Seat Cushion Heater 1. Front Seat Cushion Cover - Remove 2. Front Seat Cushion Heater - Remove NOTE: The seat cushion heater i
  • Page 119cardiagn.com 4. Front Seat Cushion Heater - Install (Si) 1. Attach the seat cushion heater to the reference position as shown. NOTE: Reference position in the vertical direction: Align the seat cushion heater edge (A) with the seat cushion pad groove (B). Reference position in the horizontal directi
  • Page 1205. All Removed Parts - Install cardiagn.com 1. Install the parts in the reverse order of removal. Front Seat-Back Heater 1. Front Seat-Back Cover - Remove 2. Front Seat-Back Heater - Remove
  • Page 121NOTE: The seat-back heater is glued to the seat-back pad. When removing it, take care not to damage the seat-back pad. 3. Front Seat-back Heater - Install (Except Si) cardiagn.com 1. Attach the seat-back heater to the reference position as shown. NOTE: Reference position in the vertical direction: A
  • Page 1224. Front Seat-back Heater - Install (Si) 1. Attach the seat-back heater to the reference position as shown. NOTE: Reference position in the vertical direction: Align the seat-back heater edge (A) with the seat-back pad groove (B). Reference position in the horizontal direction: Align the seat-back h
  • Page 1231. Rear Seat Cushion Cover - Remove 2. Rear Seat Cushion Heater - Remove cardiagn.com
  • Page 124NOTE: The seat cushion heater is glued to the seat cushion pad. When removing it, take care not to damage the seat cushion pad. cardiagn.com 3. Rear Seat Cushion Heater - Install 1. Attach the seat cushion heater to the reference position as shown. NOTE: Reference position in the vertical direction:
  • Page 1254. All Removed Parts - Install 1. Install the parts in the reverse order of removal. cardiagn.com
  • Page 126Seat Heater Replacement SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. Front Seat Cushion Heater 1. Front Seat Cushion Cover - Remove 2. Front Seat Cushion Heater - Remove NOTE: The seat cushion heater i
  • Page 127cardiagn.com 4. All Removed Parts - Install 1. Install the parts in the reverse order of removal. Front Seat-Back Heater 1. Front Seat-Back Cover - Remove 2. Front Seat-Back Heater - Remove NOTE: The seat-back heater is glued to the seat-back pad. When removing it, take care not to damage the seat-b
  • Page 1283. Front Seat-back Heater - Install 1. Attach the seat-back heater to the reference position as shown. NOTE: Reference position in the vertical direction: Align the seat-back heater edge (A) with the seat-back pad groove (B). Reference position in the horizontal direction: Align the seat-back heater
  • Page 129NOTE: The seat cushion heater is glued to the seat cushion pad. When removing it, take care not to damage the seat cushion pad. 3. Rear Seat Cushion Heater - Install cardiagn.com 1. Attach the seat cushion heater to the reference position as shown. NOTE: Reference position in the vertical direction:
  • Page 1301. Install the parts in the reverse order of removal. cardiagn.com
  • Page 131Seat Heater Switch Removal and Installation Rear Seat Heater 1. Center Console Rear Trim - Remove 2. Rear Seat Heater Switch - Remove 3. All Removed Parts - Install cardiagn.com 1. Install the parts in the reverse order of removal.
  • Page 132Seat Heater Switch Test Rear Seat Heater 1. Center Console Rear Trim - Remove 2. Rear Seat Heater Switch - Test 1. Check the rear seat heater switch (A) according to the table. NOTE: When an LED is located between terminals, check if the LED illuminates by connecting power and ground to the LED. Not
  • Page 1332. If the result is not as specified, replace the rear seat heater switch. cardiagn.com 3. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 134Seat Heater Test SRS components are located in this area. Review the SRS component locations and the precautions and procedures before doing repairs or service. Driver's Seat 1. Driver's Seat - Remove 2. Driver's Seat Heater - Test 1. Disconnect the connectors (A). 2. Check for continuity between th
  • Page 1352. Front Passenger's Seat Heater - Test 1. Disconnect the connectors (A). 2. Check for continuity between the terminals according to the table. Front Passenger's Seat Cushion Heater Connector No. 1 (4P connector) No. 2 (4P connector) No. 1 (4P connector) No. 1 (2P connector) No. 2 (4P connector) No.
  • Page 1361. Disconnect the left rear seat cushion heater connector B. 2. Check for continuity between the terminals according to the table. Left Rear Seat Cushion Heater Connector No. 1 (6P connector) No. 2 (6P connector) No. 1 (6P connector) No. 3 (6P connector) No. 4 (6P connector) No. 4 (4P connector) No.