Honda CIVIC 10G 2016 Steering Wheel And Column Page 1

Steering Component Location Index
Steering Component Location Index 1653 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD/...
1 of 1 1/28/2019 5:53 AM
cardiagn.com

Contents Summary of Steering Wheel And Column

  • Page 1Steering Component Location Index cardiagn.com
  • Page 2Steering Angle Neutral Position Learning NOTE: If the steering angle neutral position is cleared, do the steering angle neutral position learning procedure. The steering angle neutral position is cleared whenever you do any of these actions: - EPS motor/control unit replacement, removal, or installa
  • Page 3NOTE: VSA sensor neutral position memorization for VSA system is performed, the steering angle neutral position is cleared and overwritten. cardiagn.com
  • Page 4Steering Column Cover Removal and Installation 1. Upper Column Cover - Remove 1. Adjust the steering column to the full tilt down position, and to the full telescopic out position. 2. Remove the clips (A) from the upper column cover (B). 3. Turn the steering wheel 90° clockwise, and then release the
  • Page 54. Turn the steering wheel 180° counterclockwise, and then release the hook (A) with the trim tool. cardiagn.com 5. Remove the upper column cover (A). 2. Lower Column Cover - Remove
  • Page 61. Turn the steering wheel to access the screws (A), then remove the screws. cardiagn.com 2. Remove the lower column cover (A). 3. All Removed Parts - Install 1. Install the parts in the reverse order of removal.
  • Page 7Steering Column Inspection Check of Tilting Force 1. Check of Tilting Force 1. Set the steering wheel in the straight ahead driving position, and loosen the lock lever fully. 2. Attach a commercially available spring scale (A) to the highest point of the steering wheel, and tilt the steering column
  • Page 8Check of Lock Lever Force 1. Check of Lock Lever Force 1. Move the lock lever (A) from the loosened position to the locked position three to five times, then release the lock lever. Adjust the steering column to the center tilt position and also to the full telescopic out position, and hold the stee
  • Page 9cardiagn.com 3. Steering Column - Install
  • Page 10Steering Column Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before doing repairs or service. Do not release the lock lever until the steering column is installed. If the lock lever is released before i
  • Page 11Without steering lock 1. Disconnect the connectors (A) and remove the harness clips (B). 2. Remove the combination switch body assembly (C). cardiagn.com
  • Page 12With steering lock cardiagn.com 7. Steering Joint - Disconnect 8. Steering Column - Remove
  • Page 13cardiagn.com NOTE: SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before doing repairs or service. Do not release the lock lever until the steering column is installed. If the lock lever is released before installation, adjust the stee
  • Page 14cardiagn.com 2. Loosely install the attaching nuts and bolts. 3. Tighten the attaching nuts and bolts to the specified torque in the numbered sequence shown. 2. Steering Joint - Connect 3. Combination Switch Body Assembly/Wire Harness - Install
  • Page 15Without steering lock 1. Install the combination switch body assembly (A). 2. Tighten the screws (B) in the numbered sequence shown. 3. Connect the connectors (C) and install the harness clips (D). cardiagn.com
  • Page 16With steering lock cardiagn.com 4. Column Cover - Install 5. Steering Wheel - Install 6. Driver's Airbag - Install 7. 12 Volt Battery Terminal - Connect 8. Steering - Check
  • Page 17After installation, check these items: Start the engine, allow it to idle, and turn the steering wheel from lock to lock several times. Check the steering wheel spoke angle. If steering spoke angles to the right and left are not equal (steering wheel and rack are not centered), correct the engagemen
  • Page 18Steering Gearbox Disassembly and Reassembly NOTE: For these operations, refer to the complete procedure as needed. Rack end removal and installation Tie-rod end ball joint boot replacement EPS motor/control unit removal and installation 1. Steering Gearbox - Exploded View Exploded view cardiagn.com
  • Page 19cardiagn.co
  • Page 20Steering Gearbox Removal and Installation Special Tool Required Image Description/Tool Number Subframe Adapter VSB02C000016* cardiagn.com *: Available through the Honda Tool and Equipment Program, 888-424-6857. NOTE: Where icon is shown, click for further information. Where icon is shown, click for
  • Page 21cardiagn.com Detailed information, notes and precautions Replace 1. Steering Column Tilt and Telescopic Position - Set 1. Set the steering column to the center tilt position, and to the center telescopic position. 2. Vehicle - Lift
  • Page 223. Front Wheel - Remove 4. Steering Joint - Disconnect NOTE: If the center guide is in place, discard it. 5. Tie-Rod End Ball Joint - Disconnect (Both Sides) 6. Engine Undercover - Remove 7. Connector (EPS Subharness) - Disconnect cardiagn.com 1. Disconnect the connectors (A) and remove the harness
  • Page 231. Disconnect the front suspension stroke sensor connectors (A) both side. cardiagn.com 9. Front Suspension Stroke Sensor - Remove (Type-R) 1. Remove the front suspension stroke sensors both side. 10.Front Stopper Link - Disconnect (Type-R) 1. Disconnect both sides of the front stopper link from the
  • Page 2416.Exhaust Pipe A - Remove (Except Type-R) 17.Torque Rod Mounting Bolt - Remove cardiagn.com 18.Front Brace - Remove 19.Front Subframe - Remove 1. Remove both sides of the front lower arm mounting bolt from the body.
  • Page 252. Set the subframe adapter (VSB02C000016) on a transmission jack (A), line up the slots in the arms with the bolt holes on the corner of the jack base, and tighten the bolts. 3. Attach the subframe adapter to the front subframe (B). 4. Remove the front subframe with the stiffeners. cardiagn.com 20.
  • Page 26NOTE: Where icon is shown, click for further information. Where icon is shown, click for further information. Using clean solvent and a brush, wash any oil and dirt off the end of the steering gearbox. Blow dry with compressed air. Unless otherwise indicated, illustrations used in the procedure are
  • Page 27cardiagn.co
  • Page 28Detailed information, notes and precautions Torque: N·m (kgf·m, lbf·ft) Replace 1. Heat Shield, Harness, and Pinion Shaft Grommet - Install 1. Install the pinion shaft grommet (A). 2. Align the cutout portion (B) with the lug portion (C). 3. The grommet must not have a gap at the mating surface of t
  • Page 291. Tighten the steering gearbox mounting bolts and the stiffener mounting bolts to the specified torque in the sequence shown. cardiagn.com 5. Front Subframe - Install 1. Set the subframe adapter (VSB02C000016) on a transmission jack (A), line up the slots in the arms with the bolt holes on the corn
  • Page 304. Install both sides of the front lower arm mounting bolt to the body. 6. Front Brace - Install cardiagn.com 7. Torque Rod Mounting Bolt - Loosely Install 8. Subframe Jack - Release 9. Engine/Transmission Mount - Tighten 10.Exhaust Pipe A mounting Rubber - Install (Type-R)
  • Page 3111. Exhaust Pipe A - Install (Except Type-R) 12.Intake Air Resonator - Install (1.5 L engine) 13.Lower Arm Ball Joint - Connect (Both Sides) (Except Type-R) 14.Lower Arm - Connect (Type-R) 1. Connect both sides of the housing bracket ball joint from the lower arm. 15.Front Stopper Link - Connect (Ty
  • Page 321. Connect both sides of the front suspension stroke sensor connectors (A). cardiagn.com 19.Connector (EPS Subharness) - Connect 1. Connect the connectors (A) and install the harness clip (B). 20.Engine Undercover - Install 21.Tie-Rod End Ball Joint - Connect (Both Sides)
  • Page 3322.Steering Joint - Connect 23.Steering Wheel Holder Tool - Remove 24.Front Wheel - Install 25.Steering Gearbox - After Install Symptom Check 1. With the tires raised off the ground, check for the following symptoms by turning the steering wheel fully to the right and left several times. Symptom Pro
  • Page 34Steering Joint Disconnection and Reconnection 1. Steering Wheel Holder Tool - Install 1. Center the steering wheel spoke angle. 2. Install a commercially available steering wheel holder tool (A). cardiagn.com 2. Steering Joint - Disconnect 1. Remove the steering joint cover (A). 2. Hold the spline s
  • Page 35cardiagn.co
  • Page 36NOTE: How to read the torque specifications. 1. Steering Joint - Connect 1. Set the rack in the straight ahead driving position. 2. Cut the wire (A). 3. Slip the lower end of the steering joint (B) onto the pinion shaft (C). NOTE: Pinion shaft with center guide: Install the steering joint by alignin
  • Page 374. Align the bolt hole (A) on the steering joint with the groove (B) around the pinion shaft. 5. Loosely install the steering joint bolt (C). 6. Be sure that the joint bolt is securely in the groove in the pinion shaft. 7. Pull on the steering joint to make sure that the steering joint is fully seat
  • Page 38Steering Linkage and Gearbox Inspection 1. Steering Linkage and Gearbox - Inspect cardiagn.com
  • Page 39Steering Lock Removal and Installation NOTE: SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before doing repairs or service. Unless otherwise indicated, illustrations used in the procedure are for without keyless access system. 1. Stee
  • Page 401. Without keyless access system: Install the steering lock (A) without the key inserted. 2. With keyless access system: Install the electric steering lock. 3. Loosely tighten the new shear bolts (B). NOTE: The shear bolts have left-hand threads. 4. Without keyless access system: Insert the ignition
  • Page 41Steering Rack End Removal and Installation NOTE: Do not allow dust, dirt, or other foreign materials to enter the steering gearbox. 1. Steering Gearbox - Remove 2. Tie-Rod End - Remove cardiagn.com 3. Rack End Boot - Remove 1. Remove the boot band (A). 2. Remove the tie-rod clip (B). 3. Pull the boo
  • Page 42cardiagn.co
  • Page 434. Rack End - Remove 1. Hold the gearbox housing using a C-clamp (A) and wooden blocks (B) to a workbench as shown. NOTE: Do not clamp the cylinder part of the gearbox housing in a C-clamp. Be careful not to damage the mounting surface with a C-clamp. cardiagn.com 2. Hold the flat surface sections (
  • Page 441. Hold the gearbox housing using a C-clamp (A) and wooden blocks (B) to a workbench as shown. NOTE: Do not clamp the cylinder part of the gearbox housing in a C-clamp. Be careful not to damage the mounting surface with a C-clamp. 2. Install a new rubber stop (A). cardiagn.com 3. Tighten both rack e
  • Page 454. Apply multipurpose grease to the boot grooves (A). cardiagn.com
  • Page 462. Rack End Boot - Install 1. Install the boot (A) on the rack end with the tie-rod clip (B). 2. Fit the boot end in the installation grooves in the housing properly. 3. After installing the boot, wipe the grease off the threaded section (C) of the rack end. cardiagn.com 4. Install the new boot band
  • Page 475. Close the ear portion (A) of the boot band (B) with pincers Oetiker 1098, commercially available or equivalent (C). 3. Tie-Rod End - Install cardiagn.com 4. Steering Gearbox - Install
  • Page 48Steering Tie-Rod End Ball Joint Boot Replacement Special Tool Required Image Description/Tool Number Ball Joint Thread Protector, 12 mm 07AAF-SDAA100 cardiagn.com Ball Joint Remover, 28 mm 07MAC-SL00202 Driver, 32.5 mm 070AD-SAAA100 1. Vehicle - Lift
  • Page 492. Front Wheel - Remove 3. Tie-Rod End Ball Joint - Disconnect Except Type-R 1. Remove the cotter pin (A). 2. Remove the nut (B). 3. Disconnect the tie-rod end ball joint from the knuckle using the ball joint tread protector and the ball joint remover. NOTE: Be careful not to damage the ball joint b
  • Page 501. Remove the ball joint boot (A) from the tie-rod end. 2. Wipe the old grease off the ball pin. NOTE: How to read the torque specifications. cardiagn.com 1. Tie-Rod End Ball Joint Boot - Install 1. Pack the lower area of the ball pin (A) with fresh multipurpose grease. 2. Pack the interior of the n
  • Page 513. Install the ball joint boot (A) using the driver. 4. The ball joint boot must not have a gap at the ball joint boot installation sections (B). 5. After installing the ball joint boot, check the ball pin tapered section for grease contamination. 6. Wipe the ball pin tapered section if necessary. 2
  • Page 52Type-R 1. Wipe off any grease contamination from the ball joint tapered section and threads. 2. Connect the tie-rod ball joint (A) to the knuckle. 3. Install the castle nut (B). NOTE: Torque the castle nut to the lower torque specification, then tighten it only far enough to align the slot with the
  • Page 53Steering Wheel Disassembly and Reassembly 1. Steering Wheel - Exploded View Without paddle shifter cardiagn.com With paddle shifter
  • Page 54cardiagn.co
  • Page 55Steering Wheel Removal and Installation SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before doing repairs or service. 1. 12 Volt Battery Terminal - Disconnect NOTE: Wait at least 3 minutes before starting work. 2. Driver's Airbag - R
  • Page 564. Install a commercially available steering wheel puller (A) on the steering wheel (B). 5. Free the steering wheel from the steering column shaft by turning the pressure bolt (C) of the puller. Note these items when removing the steering wheel: Do not tap on the steering wheel or the steering colum
  • Page 571. Position the steering wheel hub (A) so that it engages the pin (B) of the cable reel. 2. Install the steering wheel (C) on to the steering column shaft. NOTE: Do not tap on the steering wheel or the steering column shaft when installing the steering wheel. cardiagn.com 3. Install the new steering
  • Page 582. If steering spoke angles to the right and left are not equal (steering wheel is not centered), correct the engagement of the wheel/column shaft splines. 6. VSA Sensor Neutral Position - Memorize cardiagn.com
  • Page 59Steering Wheel Rotational Play Check 1. Steering Wheel Rotational Play - Check 1. Set the front wheels in the straight ahead position. 2. Measure how far you can turn the steering wheel left and right without moving the front wheels. If the play is within the limit, the steering gearbox and the stee