Honda CIVIC 10G 2016 Tcm Page 1

TCM Connector for Inputs and Outputs
CVT Control System Inputs and Outputs at TCM 50P Connector
Terminal Number Terminal Name Description
1 +B (POWER SOURCE) Power source for TCM
2 Not used
3*
1
F-CAN_H (F-CAN COMMUNICATION SIGNAL HIGH) Sends and receives communication signal
3*
2
F-CAN A_H (F-CAN COMMUNICATION SIGNAL HIGH) Sends and receives communication signal
4 TM-CAN_H (TM-CAN COMMUNICATION SIGNAL HIGH) Sends and receives communication signal
5 Not used
6 Not used
7 SOL B (SHIFT SOLENOID VALVE B) Drives shift solenoid valve B
8 IG1 (IGNITION SIGNAL) Detects ignition signal
9 GND2(TCU) (TCM GROUND) Ground for TCM
10 GND1(TCU) (TCM GROUND) Ground for TCM
11*
1
F-CAN_L (F-CAN COMMUNICATION SIGNAL LOW) Sends and receives communication signal
11*
2
F-CAN A_L (F-CAN COMMUNICATION SIGNAL LOW) Sends and receives communication signal
12 TM-CAN_L (TM-CAN COMMUNICATION SIGNAL LOW) Sends and receives communication signal
13 CPCLS (CVT CLUTCH PRESSURE CONTROL SOLENOID VALVE) Drives CVT clutch pressure control solenoid valve
14 DNLS (CVT DRIVEN PULLEY PRESSURE CONTROL SOLENOID VALVE) Drives CVT driven pulley pressure control solenoid valve
15 DRLS (CVT DRIVE PULLEY PRESSURE CONTROL SOLENOID VALVE) Drives CVT drive pulley pressure control solenoid valve
16 LCCLS (CVT LOCK-UP CLUTCH CONTROL SOLENOID VALVE) Drives CVT lock-up clutch control solenoid valve
17 VCC4 (SENSOR VOLTAGE) Provides sensor reference voltage
18 VCC1 (SENSOR VOLTAGE) Provides sensor reference voltage
19 SG2 (SENSOR GROUND) Sensor ground
20 SG1 (SENSOR GROUND) Sensor ground
21 VCC2 (SENSOR VOLTAGE) Provides sensor reference voltage
22 VEL-PWM (CVT SPEED SENSOR) Detects CVT speed sensor signal
23 Not used
24 Not used
25 SG3 (SENSOR GROUND) Sensor ground
26 SLS (SHIFT LOCK SOLENOID) Drives shift lock solenoid
27 Not used
28 NDR-PWM (CVT DRIVE PULLEY SPEED SENSOR) Detects CVT drive pulley speed sensor signal
TCM Connector for Inputs and Outputs 4007 http://techinfo.honda.com/rjanisis/pubs/sm/1/2/Contents/enu/61TBAD...
1 of 2 2/8/2019 9:51 AM
cardiagn.com

Contents Summary of Tcm

  • Page 1TCM Connector for Inputs and Outputs CVT Control System Inputs and Outputs at TCM 50P Connector Terminal Number Terminal Name Description 1 +B (POWER SOURCE) Power source for TCM 2 Not used 3*1 F-CAN_H (F-CAN COMMUNICATION SIGNAL HIGH) Sends and receives communication signal 3*2 F-CAN A_H (F-CAN COM
  • Page 2Terminal Number Terminal Name Description 29 SG4 (SENSOR GROUND) Sensor ground 30 Not used 31 PDN (CVT DRIVEN PULLEY PRESSURE SENSOR) Detects CVT driven pulley pressure sensor signal 32 SG5 (SENSOR GROUND) Sensor ground 33 TATF (TRANSMISSION FLUID TEMPERATURE SENSOR) Detects transmission fluid tempe
  • Page 3TCM Connector for Inputs and Outputs CVT Control System Inputs and Outputs at TCM 50P Connector Terminal Number Terminal Name Description 1 +B (POWER SOURCE) Power source for TCM 2 Not used 3*1 F-CAN_H (F-CAN COMMUNICATION SIGNAL HIGH) Sends and receives communication signal 3*2 F-CAN A_H (F-CAN COM
  • Page 4Terminal Number Terminal Name Description 29 SG4 (SENSOR GROUND) Sensor ground 30 Not used 31 PDN (CVT DRIVEN PULLEY PRESSURE SENSOR) Detects CVT driven pulley pressure sensor signal 32 SG5 (SENSOR GROUND) Sensor ground 33 TATF (TRANSMISSION FLUID TEMPERATURE SENSOR) Detects transmission fluid tempe
  • Page 5TCM Removal and Installation 1. Air Cleaner - Remove 2. Intake Air Duct - Remove 3. TCM - Remove 1. Disconnect the connector (A) by pushing the lock (B) and pulling the lever (C) in the numbered sequence shown. 2. Remove the TCM (D). cardiagn.com 4. All Removed Parts - Install 1. Install the parts i
  • Page 6cardiagn.co
  • Page 7Procedure After Replacing TCM 5. TCM - Update cardiagn.com
  • Page 8TCM Removal and Installation 1. TCM - Remove 1. Disconnect the connector (A) by pushing the lock (B) and pulling the lever (C) in the numbered sequence shown. 2. Remove the TCM (D). cardiagn.com 2. All Removed Parts - Install 1. Install the parts in the reverse order of removal. NOTE: Check the conn
  • Page 9TCM Reset 1. HDS - Connect 2. TCM - Reset 1. Select the A/T SYSTEM with the HDS. 2. Reset the TCM with the HDS while the engine is stopped. 3. Turn the vehicle to the OFF (LOCK) mode. 4. Turn the vehicle to the ON mode, then wait for 30 seconds. cardiagn.com 5. Turn the vehicle to the OFF (LOCK) mod
  • Page 10TCM Reset 1. HDS - Connect 2. TCM - Reset 1. Select the A/T SYSTEM with the HDS. 2. Reset the TCM with the HDS while the engine is stopped. 3. Turn the vehicle to the OFF (LOCK) mode. 4. Turn the vehicle to the ON mode, then wait for 30 seconds. cardiagn.com 5. Turn the vehicle to the OFF (LOCK) mod
  • Page 11TCM Update NOTE: High temperature in the engine compartment might cause the TCM to become too hot to run the update. If the engine has been running before this procedure, open the hood and cool the engine compartment. 1. TCM - Update NOTE: Check any official service website for more information abou
  • Page 12TCM Update NOTE: High temperature in the engine compartment might cause the TCM to become too hot to run the update. If the engine has been running before this procedure, open the hood and cool the engine compartment. 1. TCM - Update NOTE: Check any official service website for more information abou