Hydraulic Pump

Hydraulic Tractor Troubleshooting

Skip to content
Menu
  • Home
  • Contact Us

Category: BobCat E35

BobCat E35

BobCat E35 – HYDRAULIC CONTROL VALVE – Assembly

Posted on July 27, 2022

Clean all parts in solvent and dry with compressed air. Inspect all parts for wear or damage. Replace any worn or damaged parts. Always install…

BobCat E35

BobCat E35 – HYDRAULIC CONTROL VALVE – Disassembly

Posted on July 26, 2022

Remove the four nuts (Item 1) [Figure 20-40-16]. Remove the inlet (Item 1) [Figure 20-40-17]. Remove the three O-rings (Item 1) [Figure 20-40-18]. Remove the…

BobCat E35

BobCat E35 – HYDRAULIC CONTROL VALVE – Parts Identification

Posted on July 25, 2022

 

BobCat E35

BobCat E35 – HYDRAULIC CONTROL VALVE – Removal And Installation

Posted on July 25, 2022

Lower the work group to the ground. Stop the engine. With the engine off, turn the start key to the ON position and move both…

BobCat E35

BobCat E35 – HYDRAULIC CONTROL VALVE – Description

Posted on July 20, 2022

The hydraulic control valve is a nine section closed center system and has one main relief valve. The main relief valve operates at 24476 kPa…

BobCat E35

BobCat E35 – VALVE (PILOT PRESSURE RELIEF) – Testing And Adjusting The Pilot Pressure Relief Valve

Posted on July 20, 2022

The pilot pressure valve supplies lower hydraulic pressure to joysticks. The following tools will be needed for testing the pilot pressure relief valve: MEL 1355…

BobCat E35

BobCat E35 – VALVE (CROSS PORT RELIEF) – Removal And Installation

Posted on July 18, 2022

Drain the hydraulic reservoir. (See Removing And Replacing Hydraulic Fluid on Page 10-130-5.) Remove the floor mat. (See Removal And Installation on Page 40-110-1.) Remove…

BobCat E35

BobCat E35 – VALVE (CROSS PORT RELIEF) – TEST CONDITIONS

Posted on July 17, 2022

1. Engine High Idle Speed 2. Warm oil over relief function to minimum 66°C (150°F). Cycle all functions during warm up procedure. Warm oil until…

BobCat E35

BobCat E35 – VALVE (CROSS PORT RELIEF) – Testing

Posted on July 17, 2022

The following tools will be needed for the testing at the diagnostic coupler: MEL1355 – Test Kit includes the following: MEL1355-3 – 34474 kPa (345…

BobCat E35

BobCat E35 – VALVE (PORT RELIEF) – Testing And Adjusting Port Relief Valve Pressure

Posted on July 17, 2022

When testing the port relief valves with a hydraulic hand pump, slowly pressurize the valve. If the hand pump is pumped fast, the pressure will…

Posts pagination

Previous Page Page 1 … Page 38 Page 39 Page 40 … Page 44 Next Page

Recent Posts

  • Hydrostatic Drive Problems and Solutions
  • Negative Displacement Pump Types
  • Parts of a Gear Pump and How It Works
  • Piston Pump Components and Basics
  • Principle of Gear Pump

Categories

  • BobCat 753
  • BobCat E35
  • BOBCAT S130
  • BobCat S70
  • Creation and Control of Fluid Flow
  • Hydraulic Actuators
  • Hydraulic Basics
  • Hydraulic Pressure Control
  • Hydraulic Pumps and Pressure Regulation
  • Hydrostatic Transmissions
  • Pump
  • Rotary Actuator
  • Servo Valves
  • Troubleshooting
© Copyright 2024 – Hydraulic Pump
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy