Hydraulic Pump

Hydraulic Tractor Troubleshooting

Skip to content
Menu
  • Home
  • Contact Us
BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Main Relief Valve Removal And Installation

Posted on February 25, 2022

NOTE: The main relief valve is non-adjustable. Remove the main relief valve adapter fitting (Item 1) [Figure 20-40-29]. Remove the O-ring from the main relief…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Load Check Valves Removal And Installation

Posted on February 25, 2022

Remove the BICSTM valve assembly from the control valve. (See BICSTM Valve Removal And Installation on Page 20-40-1.) Remove and discard the four large O-rings…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Disassembly And Assembly

Posted on February 25, 2022

See Identification Chart on Page 20-40-8 for the control valve parts assembly. Mark each valve section and spool so that the parts will be returned…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Identification Chart

Posted on February 25, 2022

 

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Removal And Installation

Posted on February 25, 2022

Install jackstands under the rear corners of the loader. (See Procedure on Page 10-10-1.) Raise the operator cab. (See Raising on Page 10-30-1.) Remove the…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – BICS Valve, Identification Chart

Posted on February 25, 2022
BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – BICS Valve, Solenoid Testing

Posted on February 25, 2022

Use a test meter to measure the coil resistance [Figure 20-40-17]. Coil wires do not have polarity. Correct resistance for the coil is 7-10 ohms.…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – BICS Valve, Solenoid Removal And Installation

Posted on February 25, 2022

Remove the mounting nut (Item 1) [Figure 20-40-13] from the solenoid stem. Installation: Tighten the nut to 53 in.-lb. (6 Nโ€ขm) torque. Remove the coil.…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – BICS Valve, Check Valve Removal And Installation

Posted on February 25, 2022

Remove the check valve (Item 1) [Figure 20-40-10]. Installation: Tighten the valve to 22 ft.-lb. (30 Nโ€ขm) torque. Remove the O-rings (Item 1) and back-up…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Pressure Differential Valve Removal And Installation

Posted on February 25, 2022

Remove the two pressure differential valves (Item 1) [Figure 20-40-8] from the BICS valve. Remove the O-rings (Item 1) and back-up rings (Item 2) [Figure…

Posts pagination

Previous Page Page 1 … Page 131 Page 132 Page 133 … Page 141 Next Page

Recent Posts

  • Hydrostatic Drive Problems and Solutions
  • Negative Displacement Pump Types
  • Parts of a Gear Pump and How It Works
  • Piston Pump Components and Basics
  • Principle of Gear Pump

Categories

  • BobCat 753
  • BobCat E35
  • BOBCAT S130
  • BobCat S70
  • Creation and Control of Fluid Flow
  • Hydraulic Actuators
  • Hydraulic Basics
  • Hydraulic Pressure Control
  • Hydraulic Pumps and Pressure Regulation
  • Hydrostatic Transmissions
  • Pump
  • Rotary Actuator
  • Servo Valves
  • Troubleshooting
© Copyright 2024 – Hydraulic Pump
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy