Hydraulic Pump

Hydraulic Tractor Troubleshooting

Skip to content
Menu
  • Home
  • Contact Us
BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Auxiliary Spool Disassembly And Assembly

Posted on February 25, 2022

Wrap a rag (Item 1) [Figure 20-40-72] around the detent ball retainer and the centering spring. Slowly remove the retainer from the balls. The detent…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Auxiliary Spool Removal And Installation

Posted on February 25, 2022

Remove the screws (Item 1) and rubber boot (Item 2) [Figure 20-40-69] from the linkage end of the control valve. Remove the spool seal retainer…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Tilt Spool Disassembly And Assembly

Posted on February 25, 2022

Put the linkage end of the spool in a vise and install the MEL 1285 Compression Spring Tool (Item 1) [Figure 20-40-65] Remove the bolt…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Tilt Spool Removal And Installation

Posted on February 25, 2022

Remove the lift and tilt lock block (Item 1) [Figure 20-40-61] from the control valve. (See Lift And Tilt Lock Block Removal And Installation on…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Lift Spool And Detent Disassembly

Posted on February 25, 2022

Put the linkage end of the spool assembly [Figure 20-40-48] in a vise. Install MEL1285 Spring Compressor Tool (Item 1) [Figure 20-40-48] on the spring…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Lift Spool And Detent Removal And Installation

Posted on February 25, 2022

The tool listed will be needed to do the following procedure: MEL 1278 – Detent Tool MEL 1285 – Detent Spring Tool Remove the lift…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Lift And Tilt Lock Block Removal And Installation

Posted on February 25, 2022

Remove the lift and tilt lock block [Figure 20-40-40].  

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Rubber Boot Removal And Installation

Posted on February 25, 2022

Remove the two screws (Item 1) [Figure 20-40-38] from the rubber boot retainer. Assembly: Tighten the screws to 90-100 ft.-lb. (10,2-11,3 Nโ€ขm) torque. Remove the…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Anti Cavitation/Check Valves Removal And Installation

Posted on February 25, 2022

Remove the Anti Cavitation/Check valve (Item 1) [Figure 20-40-34] from the tilt cylinder base end port. Remove the O-rings (Item 1), and back-up washer (Item…

BobCat S70

BobCat S70 – HYDRAULIC CONTROL VALVE – Port Relief/Anti-Cavitation Valve Removal And Installation

Posted on February 25, 2022

Remove the Port Relief/Anti Cavitation valve (Item 1) [Figure 20-40-32]. Assembly: Always use new O-rings and back-up washers. Tighten to 35-40 ft.-lb. (47-54 Nโ€ขm) torque.…

Posts pagination

Previous Page Page 1 … Page 130 Page 131 Page 132 … Page 141 Next Page

Recent Posts

  • Hydrostatic Drive Problems and Solutions
  • Negative Displacement Pump Types
  • Parts of a Gear Pump and How It Works
  • Piston Pump Components and Basics
  • Principle of Gear Pump

Categories

  • BobCat 753
  • BobCat E35
  • BOBCAT S130
  • BobCat S70
  • Creation and Control of Fluid Flow
  • Hydraulic Actuators
  • Hydraulic Basics
  • Hydraulic Pressure Control
  • Hydraulic Pumps and Pressure Regulation
  • Hydrostatic Transmissions
  • Pump
  • Rotary Actuator
  • Servo Valves
  • Troubleshooting
© Copyright 2024 – Hydraulic Pump
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy