Hydraulic Pump

Hydraulic Tractor Troubleshooting

Skip to content
Menu
  • Home
  • Contact Us

Category: BOBCAT S130

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (ACS) OR (SJC) – Removal And Installation

Posted on October 11, 2023

Lift and block the loader. (See Procedure on Page 10-10-1.) Raise the lift arms and install an approved lift arm support device. (See Installing on…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (ACS) OR (SJC) – Description

Posted on October 11, 2023

The hydraulic control valve is located inside the main frame on the right hand side, below the operators cab. The hydraulic control valve [Figure 20-41-1]…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Check Valve Removal And Installation

Posted on October 11, 2023

Remove the tubeline (Item 1) [Figure 20-40-118]. Remove the check valve fitting (Item 1) [Figure 20-40-119] from the hydraulic control valve. Installation: Lubricate the O-ring…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Main Relief Valve Removal And Installation

Posted on October 11, 2023

Remove the main relief valve (Item 1) [Figure 20-40-116]. Remove the O-rings (Item 1) [Figure 20-40-117] from the main relief valve. Installation: Always use new…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Lift Arm Bypass Orifice Removal And Installation

Posted on October 11, 2023

Remove the tubeline (Item 1) and fitting (Item 2) [Figure 20-40-114] from the valve. Check the lift arm bypass orifice (Item 1) [Figure 20-40-115]. NOTE:…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Lock Valve Removal And Installation

Posted on October 11, 2023

Locate the two BICS lock valves, (Item 1) is for the tilt circuit and (Item 2) [Figure 20-40-107] is for the lift circuit. Remove the…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Solenoid Removal And Installation

Posted on October 11, 2023

Remove the nut (Item 1) [Figure 20-40-103] from the solenoid stem. Installation: Tighten the nut to 53 in.-lb. (6 Nโ€ขm) torque. Remove the solenoid coil…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Auxiliary Solenoid Removal And Installation

Posted on October 11, 2023

Remove the nut (Item 1) [Figure 20-40-99] from both solenoids. Installation: Tighten the nut to 48 – 72 in.-lb. (5 – 8 Nโ€ขm) torque. Remove…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Auxiliary Spool Removal And Installation

Posted on October 11, 2023

Remove the three screws (Item 1) [Figure 20-40-93] from the spool centering block. Installation: Tighten the bolt to 90 – 100 in.-lb. (10 – 11,3…

BOBCAT S130

BOBCAT S130 – HYDRAULIC CONTROL VALVE (STANDARD) – Tilt Spool Removal And Installation

Posted on October 11, 2023

Remove the lift and tilt end cap/spool lock block. (See End Cap/Spool Lock Block Removal And Installation on Page 20-40-13.) Remove the spacer (Item 1)…

Posts pagination

Previous Page Page 1 … Page 35 Page 36 Page 37 … Page 40 Next Page

Recent Posts

  • Hydrostatic Drive Problems and Solutions
  • Negative Displacement Pump Types
  • Parts of a Gear Pump and How It Works
  • Piston Pump Components and Basics
  • Principle of Gear Pump

Categories

  • BobCat 753
  • BobCat E35
  • BOBCAT S130
  • BobCat S70
  • Creation and Control of Fluid Flow
  • Hydraulic Actuators
  • Hydraulic Basics
  • Hydraulic Pressure Control
  • Hydraulic Pumps and Pressure Regulation
  • Hydrostatic Transmissions
  • Pump
  • Rotary Actuator
  • Servo Valves
  • Troubleshooting
© Copyright 2024 – Hydraulic Pump
Wisteria Theme by WPFriendship ⋅ Powered by WordPress

Privacy Policy